3Doodler Flow - User Manual

1
EN11/2023
SECTION 1: WARNINGSSECTION 1: WARNINGS
WHAT’S INCLUDEDWHAT’S INCLUDED
- The Nozzle of the 3Doodler Flow
can become hot. DO NOT touch
the Nozzle, or you may be burned!
- DO NOT allow the Nozzle near or in
contact with flammable materials.
- Inform others in the area that the
Pen is hot and should not be
touched.
Unplug to turn the pen OFF when not
in use or before storing.
Allow the Nozzle to cool
completely before storing.
The Unblocking Tool can become
hot. DO NOT touch the metal part
of the Unblocking Tool after using
it to clean your 3Doodler Flow or
you may burn yourself!
DO NOT use the 3Doodler Flow near
bathtubs, showers, basins or other
vessels containing water. This
could result in death due to electric
shock.
The 3Doodler Flow should only be
used with 3Doodler Flow plastic
filament. Misuse of your 3Doodler
Flow, setting your pen to the wrong
heating temperature, or use of non-
approved plastic filament or other
materials may result in damage to
your pen or injury to you, and will
void your warranty. Injuries to the
user may include, but are not limited
to, harm sustained from inhaling
substances that are not suitable for
heating; or burns from flammable
materials used in the 3Doodler Flow.
ADULT USE ONLY. KEEP OUT OF REACH OF CHILDREN.ADULT USE ONLY. KEEP OUT OF REACH OF CHILDREN.
Disposal of this product
At the end of your 3Doodler Flow’s life, please do not dispose of
it in your general household waste. In order to prevent possible
harm to the environment or human health from uncontrolled
waste disposal, please dispose of your 3Doodler Flow
separately in accordance with local laws and regulations.
WARNING: This 3D Printing
Device, when used with a styrene
filament (ABS / HIPS / or PC-
ABS), can expose you and others
in the same room to styrene,
which is a chemical known to
the State of California to cause
cancer. For more information,
go to
www.P65Warnings.ca.gov.
ALWAYS OPERATE YOUR 3D
PRINTING DEVICE IN A WELL-
VENTILATED AREA.
For more information on the separate collection systems for
waste of electrical and electronic equipment, please contact
your local municipal authority. You can also contact the retailer
from which you purchased your 3Doodler Flow, who may have
a recycling program, or be part of a specific recycling scheme
that you can use.
User Manual
3Doodler
Flow Pen
8 3Doodler
1.75mm Plastic
Spools
Colors may
vary
Tool
Power
Adapter
SECTION 1: WARNINGSSECTION 1: WARNINGS

Summary

SECTION 1: WARNINGS

Nozzle and Flammability Hazards

Warnings about hot nozzle, contact with flammables, and informing others.

Electrical and Chemical Safety

Warnings about water hazards, styrene exposure (Prop 65), and ventilation.

STEP 2: Load and extrude plastic

Select and Insert Spool

Instructions for selecting a filament spool and inserting it into the pen.

Extrude Plastic

STEP 5: Reverse and remove plastic

Plastic Reversal Process

SECTION 3: TROUBLESHOOTING

Power and Initial Extrusion Issues

Troubleshooting for pen not turning on and plastic not extruding properly.

Plastic Reversal Issues

Troubleshooting for reversing plastic, including when it cannot be fully removed.

Plastic Adhesion and Extrusion Flow

Pen Not Heating Up

Steps to resolve issues where the pen's LED light remains red and it doesn't heat up.

Plastic Removal and Short Filament

Addressing issues with plastic removal, including when it's too short to extract.

Pen Resets During Use

Troubleshooting advice for when the pen resets itself during operation.

3Doodler Flow Specifications

General

Brand	3Doodler
Model	Flow
Category	3D Printers
Language	English