3M Ranger 245 Service Manual (English)

Other manuals for 3M Ranger 245

Service Manual22 pages

Competency Checklist2 pages

Questions and Answers:

R
Robert BakerAug 21, 2025
What to do if 3M Ranger 245 warming unit shows high temperature alert?
- W
  wwilsonAug 21, 2025
  If the 3M Medical Equipment warming unit's alphanumeric display flashes a temperature of 43°C (Model 245) or 48°C (Model 247) or higher, along with the word “HI,” and the alert indicator illuminates with a sound, consider these possibilities: * If an extreme change in flow rates occurred, open the flow to reduce the temperature. The alerts will stop when the display reads 41°C, and the unit will be ready to use. * If the unit reached the set point temperature before the cassette was inserted, the alerts will stop when the display reads 41°C, making the unit ready for use. * If fluids were prewarmed above 42°C, turn off the unit, discontinue the infusion, and avoid prewarming fluids before using the Ranger warming unit.
C
Christine LloydAug 23, 2025
What to do if my 3M Ranger 245 Medical Equipment alerts sound but unit has been turned off?
- S
  Stacy TuckerAug 23, 2025
  If the 3M Medical Equipment continues to alert even after being turned off, it means that the independent backup safety system has been activated. Unplug the unit. Also, ensure the over-temperature screw is completely tightened. If it is missing, turn the unit off, unplug it.
L
Luke TaylorAug 25, 2025
What to do if 3M Ranger 245 alerts sound, alphanumeric display and alert indicator light go dark?
- W
  wallmarkAug 25, 2025
  If the alert sounds, the alphanumeric display and alert indicator light go dark on your 3M Medical Equipment, this indicates a primary controller failure, and the unit will no longer operate. Turn the unit off and unplug it. Discontinue use of the unit and discard the warming set. Note that the alert will continue to sound if you do not unplug the unit.
G
George JacksonAug 27, 2025
Why nothing illuminates on the 3M Medical Equipment warming unit panel?
- M
  Mary BrownAug 27, 2025
  If nothing illuminates on the warming unit panel of your 3M Medical Equipment, it could be due to several reasons: * The unit is not turned on. * The unit is not plugged in, or the power cord is not correctly plugged into an appropriate outlet. Ensure the power cord is plugged into the power entry module of the warming unit. * There may be a unit failure. Check the fuses.
C
Chris BaileyAug 27, 2025
What to do if my 3M Medical Equipment alerts soon after plugging it in?
- A
  Adrian HerreraAug 28, 2025
  If your 3M Medical Equipment alerts soon after plugging it in, it might be due to a loose or missing over-temperature screw on the bottom of the unit. Make sure the over-temperature screw is completely tightened. If it is missing, turn the unit off and unplug it.
B
Barbara LopezAug 29, 2025
How to remove cassette from 3M Ranger 245 Medical Equipment?
- D
  Diane AveryAug 29, 2025
  To remove the cassette from the 3M Medical Equipment, ensure that: * Fluid is drained from the cassette before sliding it out. * Fluids are no longer infusing. * The clamp is closed proximal to the warming cassette. Also, if the warming unit is below the patient level, raise it above the patient level to avoid excessive back pressure.
A
Alyssa CantuAug 31, 2025
What to do if 3M Medical Equipment alphanumeric display reads “Er 5” or “Open.”?
- C
  Christine BrownAug 31, 2025
  If the alphanumeric display on your 3M Medical Equipment reads “Er 5” or “Open,” it indicates electrical interference. Remove the unit and refer to a biomedical technician.
C
Chelsey SharpSep 2, 2025
What to do if 3M Ranger 245 Medical Equipment warming unit displays low temperature alert?
- C
  cindy45Sep 2, 2025
  If the 3M Medical Equipment warming unit's alphanumeric display flashes a temperature of 33°C or below along with the word “LO,” and the alert indicator illuminates with a sound, the alert should stop when the temperature rises above 33°C. This under-temperature condition may be caused by very high flow using very cold fluid, or a defective heater/relay. If the alert continues, turn off the unit, unplug it, and discontinue use.
M
Melissa SantosSep 3, 2025
What to do if 3M Medical Equipment alphanumeric display reads “Er 4” or “Open.”?
- C
  Chelsea TaylorSep 3, 2025
  If the alphanumeric display on your 3M Medical Equipment reads “Er 4” or “Open,” it indicates an open wire on the temperature sensor. Do not use the unit.
J
James FletcherSep 5, 2025
How to fix a 3M Laboratory Equipment warming unit when nothing illuminates on the panel?
- R
  Robert MannSep 5, 2025
  If nothing illuminates on the warming unit panel, first, ensure the unit is turned on and properly plugged into both the power entry module and a grounded outlet. Then check the fuses. If the issue persists, it may indicate a unit failure.