3M Ranger 247 Service Manual (English)

Other manuals for 3M Ranger 247

Questions and Answers:

A
amber80Aug 23, 2025
What to do if the 3M Ranger 247 warming unit displays a high temperature alert?
- J
  Jill GonzalezAug 23, 2025
  If the alert indicator illuminates and you hear alert sounds, and the display flashes a temperature of 48°C or higher along with the word “HI,” it indicates a temporary over-temperature condition. This can happen due to rapid changes in flow rates, starting the unit before inserting the warming cassette, or using fluids pre-warmed above 42°C. To resolve this, increase the flow to lower the temperature. The alerts will stop when the temperature drops below 48°C, and the unit will be ready for use. If this doesn't work, turn off and unplug the unit, stop the fluid infusion, and avoid pre-warming fluids before using the 3M Ranger irrigation fluid warming unit.
K
Kevin RossSep 1, 2025
What to do if the 3M Ranger 247 Medical Equipment warming unit displays a low temperature alert?
- I
  ijohnsonSep 1, 2025
  If the alert indicator illuminates, alert sounds, and the display flashes a temperature of 33°C or below along with the word “LO,” it indicates an under-temperature condition. This can be caused by very high flow using very cold fluid, or a defective heater/relay. The alerts should stop when the temperature rises above 33°C. If alerts continue, turn off the unit, unplug it, and discontinue use. Call 3M Patient Warming technical support.
R
Richard ReyesAug 30, 2025
What to do if the 3M Medical Equipment warming unit alerts and the display goes dark?
- M
  Mary BerryAug 31, 2025
  If the alert sounds, the display goes dark, and the alert indicator light illuminates, it indicates a primary controller failure. Turn off and unplug the unit, discontinue its use, and discard the disposable set. The alert will continue to sound if you do not unplug the unit. Call 3M Patient Warming technical support.
N
Norman YuAug 29, 2025
What to do if the 3M Medical Equipment warming unit display reads 'Er 4' or 'Open'?
- M
  mramirezAug 29, 2025
  If the alpha-numeric display reads “Er 4” or “Open,” it indicates an open wire on the temperature sensor. Do not use the unit and call 3M Patient Warming technical support.
K
Kenneth DavisAug 28, 2025
Why can't I remove the cassette from the 3M Ranger 247 Medical Equipment warming unit?
- I
  ivaughnAug 28, 2025
  If you cannot remove the cassette from the unit, it might be too full, fluids may still be infusing, or the clamp proximal to the warming cassette might be open. Ensure the fluid is drained from the warming cassette before attempting to slide it out, confirm that fluids are no longer infusing, and verify that the clamp proximal to the warming cassette is closed. Also, if the warming unit is below the patient level, raise it above the patient level.
C
caustinAug 27, 2025
What to do if the 3M Ranger 247 Medical Equipment warming unit display reads 'Er 5' or 'Open'?
- S
  Stacy PorterAug 27, 2025
  If the alpha-numeric display shows “Er 5” or “Open,” it indicates electrical interference. Remove the unit and call 3M Patient Warming technical support.
M
Matthew JensenAug 27, 2025
What to do if the 3M Ranger 247 Medical Equipment warming unit alerts soon after plugging it in?
- W
  williamstiffanyAug 27, 2025
  If the unit alerts shortly after being plugged in, check the test screw on the bottom of the unit. Ensure it is completely tightened. If the screw is missing, turn off and unplug the unit. Call 3M Patient Warming technical support.
J
Jason BuckAug 25, 2025
What to do if nothing illuminates on the 3M Ranger 247 Medical Equipment warming unit panel?
- M
  Miguel BaldwinAug 26, 2025
  If nothing illuminates on the warming unit panel, first ensure the unit is turned on and properly plugged into both the power entry module and a grounded outlet. If the issue persists, call 3M Patient Warming technical support.
A
Anthony GillAug 25, 2025
What to do if my 3M Ranger 247 Medical Equipment warming unit alerts after being turned off?
- H
  hahncarolAug 25, 2025
  If the warming unit continues to sound alerts even after being turned off, it means the independent backup safety system has been activated. To stop the alerts, unplug the unit. Call 3M Patient Warming technical support.