ABB 2000 Series - User Manual

ABB Automation Inc.
Instrumentation Division
125 E. County Line Road
Warminster, PA 18974 USA
Tel: +1 215-674-6000
Fax: +1 215-674-7183
ABB Automation
Customer Support
ABB Instrumentation provides a comprehensive after sales service via a
Worldwide Service Organization. Contact one of the following offices for details on
your nearest Service and Repair Centre.
United Kingdom
ABB Kent-Taylor Limited
Tel: +44 (0)1480 475321
Fax: +44 (0)1480 470787
United States of America
ABB Instrumentation Inc.
Tel: +1 716 2926050
Fax: +1 716 2736207
Client Warranty
Prior to installation, the equipment referred to in this manual must be stored
in a clean, dry environment, in accordance with the Company's published
specification. Periodic checks must be made on the equipment's condition.
In the event of a failure under warranty, the following documentation must be
provided as substantiation:
1. A listing evidencing process operation and alarm logs at time of failure.
2. Copies of operating and maintenance records relating to the alleged faulty
unit.
Use of Instructions
Although Warning hazards are related to personal injury, and Caution hazards
are associated with equipment or property damage, it must be understood that
operation of damaged equipment could, under certain operational conditions,
result in degraded process system performance leading to personal injury or
death. Therefore, comply fully with all Warning and Caution notices.
Information in this manual is intended only to assist our customers in the efficient
operation of our equipment. Use of this manual for any other purpose is
specifically prohibited and its contents are not to be reproduced in full or part
without prior approval of Technical Communications Department, ABB Kent-Taylor.
Health and Safety
To ensure that our products are safe and without risk to health, the following
points must be noted:
1. The relevant sections of these instructions must be read carefully before
proceeding.
2. Warning labels on containers and packages must be observed.
3. Installation, operation, maintenance and servicing must only be carried out
by suitably trained personnel and in accordance with the information
given.
4. Normal safety precautions must be taken to avoid the possibility of an
accident occurring when operating in conditions of high pressure and/or
temperature.
5. Chemicals must be stored away from heat, protected from temperature
extremes and powders kept dry. Normal safe handling procedures must be
used.
6. When disposing of chemicals ensure that no two chemicals are mixed.
Safety advice concerning the use of the equipment described in this manual
or any relevant hazard data sheets (where applicable) may be obtained from
the Company address on the back cover, together with servicing and spares.
Series 2000 Pressure Transducer
The Company's policy is one of continuous product
improvement and the right is reserved to modify the
information contained herein without notice.
© ABB 1997 Printed in UK (6.97)
ABB Instrumentation Ltd.
St. Neots,
Cambs.
England, PE19 8EU
Tel: (01480) 475321
Fax: (01480) 217948
IM/2000 Issue 1
Warning.
An instruction that draws attention
to the risk of injury or death.
Caution.
An instruction that draws attention
to the risk of damage to the product,
process or surroundings.
Note.
Clarification of an instruction or
additional information.
Information.
Further reference for more detailed
information or technical details.
User Guide

Summary

Health and Safety

Customer Support

Client Warranty

Introduction

Mechanical Installation

Pressure Connections

Specifies G1/4 external connection compatibility with ISO 228 standard.

Environmental Limits

Defines the operational temperature range for the sensor.

Dimensions

Provides physical dimensions of the sensor in millimeters and inches.

Electrical Installation

Electrical Connections

Details pin assignments and electrical specifications for connections.

Grounding

Guidance on proper grounding for RFI protection.

Resistive Loading

Specifies permissible resistive load in the loop based on supply voltage.

Applying Power

Instruction to ensure correct polarity and excitation levels before powering.

Calibration

Information on factory calibration based on order identification code.

Maintenance

Routine Inspection

Periodic checks on cable and connector condition.

Repair

Guidance on returning damaged instruments for repair or replacement.

ABB 2000 Series Specifications

General

Series	2000 Series
Type	DC Drive
Supply Voltage	380-480 V AC
Control Mode	Speed, Torque
Protection	Overcurrent, Overvoltage, Overtemperature
Communication	Profibus, Modbus
Control Method	Digital control with microprocessor
Enclosure Rating	IP54
Cooling Method	Air or liquid cooling