ABB REB650 - Page 27

To Next Page

To Previous Page

Function block name Edition 1 logical nodes Edition 2 logical nodes

VSGAPC VSGGIO VSGAPC

WRNCALH WRNCALH WRNCALH

ZCLCPSCH ZCLCPLAL ZCLCPSCH

ZCPSCH ZCPSCH ZCPSCH

ZCRWPSCH ZCRWPSCH ZCRWPSCH

ZCVPSOF ZCVPSOF ZCVPSOF

ZMFPDIS ZMFLLN0

PSFPDIS

ZMFPDIS

ZMFPTRC

ZMMMXU

PSFPDIS

ZMFPDIS

ZMFPTRC

ZMMMXU

1MRK 505 388-UEN B Section 1

Introduction

Busbar protection REB650 2.2 IEC 21

Application manual

Main Page

Default Chapter7
- Table of Contents7
Section 1 Introduction19
- This Manual19
  - Presumptions for Technical Data19
- Intended Audience20
- Product Documentation20
- Document Symbols and Conventions23
  - Symbols23
  - Document Conventions24
- IEC 61850 Edition 1 / Edition 2 Mapping24
Section 2 Application29
- General IED Application29
- Main Protection Functions30
- Back-Up Protection Functions30
- Control and Monitoring Functions31
- Communication34
- Basic IED Functions36
Section 3 Configuration39
- Description of Configuration REB65039
  - Introduction39
    - Description of A0339
Section 4 Analog Inputs41
- Introduction41
- Setting Guidelines41
  - Setting of the Phase Reference Channel42
    - Example42
  - Setting of Current Channels42
Section 5 Local HMI69
- Display70
- Leds72
- Keypad73
- Local HMI Functionality75
Section 6 Differential Protection79
- High Impedance Differential Protection, Single Phase HZPDIF79
  - Identification79
  - Application79
Section 7 Current Protection97
- Directional Phase Overcurrent Protection, Four Steps OC4PTOC97
- Directional Residual Overcurrent Protection, Four Steps EF4PTOC108
- Four Step Directional Negative Phase Sequence Overcurrent Protection NS4PTOC117
- Thermal Overload Protection, Two Time Constants TRPTTR123
- Breaker Failure Protection CCRBRF129
- Pole Discordance Protection CCPDSC133
Section 8 Voltage Protection137
- Two Step Undervoltage Protection UV2PTUV137
Section 9 Secondary System Supervision151
- Fuse Failure Supervision FUFSPVC151
Section 10 Control157
- Apparatus Control157
- Logic Rotating Switch for Function Selection and LHMI Presentation SLGAPC172
- Selector Mini Switch VSGAPC174
- Generic Communication Function for Double Point Indication DPGAPC175
- Single Point Generic Control 8 Signals SPC8GAPC176
  - Identification176
  - Application176
- Automationbits, Command Function for DNP3.0 AUTOBITS177
- Single Command, 16 Signals SINGLECMD178
Section 11 Logic181
- Tripping Logic SMPPTRC181
- Trip Matrix Logic TMAGAPC187
- Logic for Group Alarm ALMCALH188
  - Identification188
  - Setting Guidelines189
- Logic for Group Alarm WRNCALH189
  - Identification189
    - Application189
- Logic for Group Indication INDCALH189
  - Setting Guidelines190
- Configurable Logic Blocks190
  - Application190
    - Configuration190
- Fixed Signal Function Block FXDSIGN191
  - Identification191
  - Application191
- Boolean 16 to Integer Conversion B16I192
  - Identification192
  - Application193
- Boolean to Integer Conversion with Logical Node194
- Representation, 16 Bit BTIGAPC194
  - Identification194
  - Application194
- Integer to Boolean 16 Conversion IB16195
  - Identification195
  - Application195
- Integer to Boolean 16 Conversion with Logic Node196
- Representation ITBGAPC196
  - Identification196
  - Application196
- Elapsed Time Integrator with Limit Transgression and Overflow Supervision TEIGAPC197
- Comparator for Integer Inputs - INTCOMP198
- Comparator for Real Inputs - REALCOMP200
Section 12 Monitoring203
- Measurement203
- Gas Medium Supervision SSIMG213
- Liquid Medium Supervision SSIML215
- Breaker Monitoring SSCBR216
- Event Function EVENT220
- Disturbance Report DRPRDRE222
Section 13 Metering233
- Pulse-Counter Logic PCFCNT233
Section 14 Ethernet-Based Communication237
- Access Point237
Section 15 Station Communication243
- Communication Protocols243
- IEC 61850-8-1 Communication Protocol243
- IEC/UCA 61850-9-2LE Communication Protocol247
- LON Communication Protocol261
  - Application261
  - MULTICMDRCV and MULTICMDSND262
- SPA Communication Protocol263
  - Setting Guidelines264
- IEC 60870-5-103 Communication Protocol266
- DNP3 Communication Protocol274
  - Application274
Section 16 Security275
- Authority Status ATHSTAT275
  - Application275
- Self Supervision with Internal Event List INTERRSIG275
- Change Lock CHNGLCK276
  - Application276
- Denial of Service SCHLCCH/RCHLCCH277
  - Application277
  - Setting Guidelines277
Section 17 Basic IED Functions279
- IED Identifiers TERMINALID279
Section 18 Requirements299
- Current Transformer Requirements299
- Voltage Transformer Requirements307
- SNTP Server Requirements308
- PTP Requirements308
- IEC/UCA 61850-9-2LE Merging Unit Requirements308
Section 19 Glossary311

ABB REB650 - Page 27

Table of Contents

Other manuals for ABB REB650

Related product manuals