ABB REB650 - Glossary of Technical Terms; Glossary of DNP3 and Related Terms

To Next Page

To Previous Page

Rres

Rct Rct

a) Through load situation

b) Through fault situation

c) Internal faults

Protected Object

IEC05000427-2-en.vsd

IEC05000427 V2 EN-US

Figure 32: The high impedance principle for one phase with two current

transformer inputs

1MRK 505 388-UEN B Section 6

Differential protection

Busbar protection REB650 2.2 IEC 79

Application manual

Main Page

Default Chapter7
- Table of Contents7
Section 1 Introduction19
- This Manual19
  - Presumptions for Technical Data19
- Intended Audience20
- Product Documentation20
- Document Symbols and Conventions23
  - Symbols23
  - Document Conventions24
- IEC 61850 Edition 1 / Edition 2 Mapping24
Section 2 Application29
- General IED Application29
- Main Protection Functions30
- Back-Up Protection Functions30
- Control and Monitoring Functions31
- Communication34
- Basic IED Functions36
Section 3 Configuration39
- Description of Configuration REB65039
  - Introduction39
    - Description of A0339
Section 4 Analog Inputs41
- Introduction41
- Setting Guidelines41
  - Setting of the Phase Reference Channel42
    - Example42
  - Setting of Current Channels42
Section 5 Local HMI69
- Display70
- Leds72
- Keypad73
- Local HMI Functionality75
Section 6 Differential Protection79
- High Impedance Differential Protection, Single Phase HZPDIF79
  - Identification79
  - Application79
Section 7 Current Protection97
- Directional Phase Overcurrent Protection, Four Steps OC4PTOC97
- Directional Residual Overcurrent Protection, Four Steps EF4PTOC108
- Four Step Directional Negative Phase Sequence Overcurrent Protection NS4PTOC117
- Thermal Overload Protection, Two Time Constants TRPTTR123
- Breaker Failure Protection CCRBRF129
- Pole Discordance Protection CCPDSC133
Section 8 Voltage Protection137
- Two Step Undervoltage Protection UV2PTUV137
Section 9 Secondary System Supervision151
- Fuse Failure Supervision FUFSPVC151
Section 10 Control157
- Apparatus Control157
- Logic Rotating Switch for Function Selection and LHMI Presentation SLGAPC172
- Selector Mini Switch VSGAPC174
- Generic Communication Function for Double Point Indication DPGAPC175
- Single Point Generic Control 8 Signals SPC8GAPC176
  - Identification176
  - Application176
- Automationbits, Command Function for DNP3.0 AUTOBITS177
- Single Command, 16 Signals SINGLECMD178
Section 11 Logic181
- Tripping Logic SMPPTRC181
- Trip Matrix Logic TMAGAPC187
- Logic for Group Alarm ALMCALH188
  - Identification188
  - Setting Guidelines189
- Logic for Group Alarm WRNCALH189
  - Identification189
    - Application189
- Logic for Group Indication INDCALH189
  - Setting Guidelines190
- Configurable Logic Blocks190
  - Application190
    - Configuration190
- Fixed Signal Function Block FXDSIGN191
  - Identification191
  - Application191
- Boolean 16 to Integer Conversion B16I192
  - Identification192
  - Application193
- Boolean to Integer Conversion with Logical Node194
- Representation, 16 Bit BTIGAPC194
  - Identification194
  - Application194
- Integer to Boolean 16 Conversion IB16195
  - Identification195
  - Application195
- Integer to Boolean 16 Conversion with Logic Node196
- Representation ITBGAPC196
  - Identification196
  - Application196
- Elapsed Time Integrator with Limit Transgression and Overflow Supervision TEIGAPC197
- Comparator for Integer Inputs - INTCOMP198
- Comparator for Real Inputs - REALCOMP200
Section 12 Monitoring203
- Measurement203
- Gas Medium Supervision SSIMG213
- Liquid Medium Supervision SSIML215
- Breaker Monitoring SSCBR216
- Event Function EVENT220
- Disturbance Report DRPRDRE222
Section 13 Metering233
- Pulse-Counter Logic PCFCNT233
Section 14 Ethernet-Based Communication237
- Access Point237
Section 15 Station Communication243
- Communication Protocols243
- IEC 61850-8-1 Communication Protocol243
- IEC/UCA 61850-9-2LE Communication Protocol247
- LON Communication Protocol261
  - Application261
  - MULTICMDRCV and MULTICMDSND262
- SPA Communication Protocol263
  - Setting Guidelines264
- IEC 60870-5-103 Communication Protocol266
- DNP3 Communication Protocol274
  - Application274
Section 16 Security275
- Authority Status ATHSTAT275
  - Application275
- Self Supervision with Internal Event List INTERRSIG275
- Change Lock CHNGLCK276
  - Application276
- Denial of Service SCHLCCH/RCHLCCH277
  - Application277
  - Setting Guidelines277
Section 17 Basic IED Functions279
- IED Identifiers TERMINALID279
Section 18 Requirements299
- Current Transformer Requirements299
- Voltage Transformer Requirements307
- SNTP Server Requirements308
- PTP Requirements308
- IEC/UCA 61850-9-2LE Merging Unit Requirements308
Section 19 Glossary311

ABB REB650 - Glossary of Technical Terms; Glossary of DNP3 and Related Terms

Table of Contents

Other manuals for ABB REB650

Related product manuals