Need help?Do you have a question about the AC Infinity CLOUDLINE S4 and is the answer not in the manual?
General| Model | CLOUDLINE S4 |
|---|---|
| Fan Size | 4 inches |
| Type | Inline Duct Fan |
| Airflow | 205 CFM |
| Voltage | 120V AC |
| Bearings | Dual ball bearings |
Key safety instructions to reduce the risk of fire, electric shock, or injury.
Keep probe cord away from ballast cords to ensure accurate climate detection.
Plug grow light and fan into separate power strips/sockets to prevent interference.
Features precise speed control, reduced noise, and energy efficiency.
Hydro-mechanical stator blades enable efficient airflow in high static pressure environments.
Automation controls for temperature, humidity, timer, and schedules.
Sealed to IP-44 standards, high resistance to liquids and dust.
Motor with 67,000 hour lifespan, allows mounting in any direction.
Single button controller with circular display for fan speed control (ten speeds).
Step-by-step instructions for securely mounting the fan unit.
Instructions for using straps to hang the fan unit securely.
Guide on using rope hangers for fan installation.
Steps to unscrew, rotate, and reapply screws for the motor cap.
Guidance on setting up the fan as intake or exhaust for optimal ventilation.
Instructions for connecting and powering the S-Series fan system.
Steps for connecting the T-Series fan system, including probe setup.
Guide for mounting the controller on a wall.
Instructions for mounting the controller on a steel surface using its magnet.
Method for mounting the controller using a plate.
Guide for mounting the T-Series controller on a wall.
Instructions for mounting the T-Series controller on a steel surface.
Method for mounting the T-Series controller using a plate.
Options for routing controller cords neatly.
How to use the kickstand for desktop placement.
Use adapter to connect inline fans with 4-pin Molex to the controller.
Connect devices with female UIS ports at an extended range.
Connect multiple devices via a single port for expanded connectivity.
Connect multiple fans to the Controller 69 simultaneously.
Use adapter to connect fans to the Universal Controller.
Connect mix-and-matched devices using dongles.
Connect multiple dongles to create longer device chains.
Control fan speed from 0-10 using the single button controller.
Turn the fan ON or OFF by holding the speed button for 4 seconds.
Explains various controller modes like OFF, ON, AUTO, TIMER, CYCLE, SCHEDULE.
Details on Probe Temp, Probe Humidity, Alerts, Current Level, Countdown, Current Time, User Setting.
Navigate between ALL, 1, 2, 3, and 4 ports for programming.
Set simultaneous programming for all connected devices.
Set individual programming for each connected device.
Sets the minimum level and controls device operation when OFF.
Sets the maximum level for device operation when ON.
Activates devices when temperature meets or exceeds a set threshold.
Activates devices when temperature meets or falls below a set threshold.
Activates devices when humidity meets or exceeds a set threshold.
Activates devices when humidity meets or falls below a set threshold.
Set a countdown to trigger devices to turn ON.
Set a countdown to trigger devices to turn OFF.
Set durations for devices to cycle continuously ON and OFF.
Set daily ON and OFF clock times for device scheduling.
Adjust display brightness and auto-dimming.
Turn the controller display ON or OFF, and lock settings.
Change displayed units between Fahrenheit and Celsius.
Adjust the current clock time on the controller.
Adjust the temperature reading from the sensor probe.
Adjust the humidity reading from the sensor probe.
Customize device ramp-up levels based on temperature changes.
Customize device ramp-up levels based on humidity changes.
Explains icons for Advance Programming, Auto Mode, and Timer alerts.
Shows when an advance program set in the app is active.
Flashes when auto mode triggers activate devices.
Flashes when countdowns complete for Timer, Cycle, or Schedule modes.
Indicates when the controller is connected to the app via Bluetooth.
Notifies when the controller is locked and attempts to adjust it.
Alerts when temperature/humidity meet trigger points set in the app.
Determine the maximum level the device runs at when triggered ON.
Set a minimum level for continuous operation until triggered ON.
Resets controller to factory settings, clearing user parameters.
Locks the controller to prevent parameter adjustments or mode changes.
Locks settings and turns off the display while programs continue running.
Quickly navigate to the OFF Mode from any other mode.
Resets current mode or setting value to OFF/Default.
Automatically increase or decrease user setting by holding buttons.
Steps to power on and pair your device with the AC Infinity app.
To Next Page