Acer P206H - User Manual

LCD Monitor Quick Setup Guide
English
Safety Instructions
Observe the fol owing safety guidelines when connection and using your monitor:
· Be sure that your monitor is electrically rated to operate with the AC power available inyour location.
· Locate your monitor near an easily accessible electrical outlet.
· Place the monitor on a solid surface and treat it carefully. The screen can be damaged if dropped, sharply hit, or touched
with a sharp or abrasive implement.
· Put your monitor in a location with low humidity and a minimum of dust.
· Never use your monitor if the power cable has been damaged. Do not allow anything to rest on the power cable, and keep
the cable away from where people could trip over it.
· Never insert anything metallic into the monitor openings. Doing so may create the danger of electric shock.
· To avoid electric shock, never touch the inside of the monitor. Only a qualified technician should open the monitor’s case.
· Be sure to hold the plug, not the cable, when disconnecting the monitor from an electrical outlet.
· Openings in the monitor cabinet are provided for ventilation. To prevent overheating, these openings should not be
blocked or covered. Also, avoid using the monitor on a bed, sofa, rug, or other soft surface.
· Doing so may block the ventilation openings in the bottom of the cabinet. If you put the monitor in a bookcase or some
other enclosed space, be sure to provide adequate ventilation.
· Do not expose the monitor to rain or use it near water. If the monitor accidentally gets wet, unplug it and contact an
authorized dealer immediately. You can clean the exterior of the monitor with a damp cloth when necessary, but be sure
to unplug the monitor first. If your monitor does not operate normally-in particular, if there are any unusual sounds or smells
coming from it -unplug the monitor immediately and contact an authorized dealer or service center.
Connecting Your Monitor to a Computer
2.
Connect power cord
Connect the power cord to the monitor, then to a properly grounded AC outlet.
3.
Connect the Audio Cable.(optional)
4. Power-ON Monitor and Computer
Power-ON the monitor first, then power-ON the computer.
This sequence is very important.
5. If the monitor still does not function properly, please refer to the troubleshooting section to diagnose the problem.
Troubleshooting Tips
No Power - The monitor’s power indicator is off.
Make sure the monitor power cable is fully inserted in the monitor’s power port and the electrical outlet.
Test the electrical oulet by plugging in a working electrical device such as a lamp.
Try another power cable on the monitor. You can use the computer’s power cable to perform this test.
No Video - The monitor’s power indicator is on but there are no
image on the screen.
Ensure that the video connector is properly connected to the computer.
Ensure that the computer is on and functioning properly.
Turn off the monitor and check the video cable pins. Make sure no pins are bent.
Operationg Detail
Please refer to user’s guide in CD-ROM packaged with this monitor
l
1. 1-1 Connect Video Cable
a. Make sure both the monitor and computer are powered-OFF.
b. Connect the video cable to the computer.
(only Dual-Input Model) Connect one end of the 24-pin DVI cable to the back of the monitor and connect the other
end to the computer’s port.
1-2

Summary

Safety Instructions

Connecting Your Monitor to a Computer

Connect Video Cable

Connect the video cable to the computer, ensuring both devices are powered off.

Connect Audio Cable (Optional)

Connect the audio cable if your setup requires it.

Connect Power Cord

Connect the power cord to the monitor and a properly grounded AC outlet.

Power On Monitor and Computer

Power on the monitor first, then the computer, in the correct sequence.

Troubleshooting Tips

No Power

Check power cable connections and test the outlet and cable.

No Video

Verify video connector, computer status, and check video cable pins.

Operating Detail

Refer to the user's guide in the CD-ROM for detailed operation information.

Regulations and Safety Notices

FCC Notice

Information on FCC compliance for Class B digital devices and interference.

CE Declaration of Conformity

Acer Inc. declares compliance with EU directives for EMC, Low Voltage, and RoHS.

Shielded Cables and Peripherals

Use shielded cables and Class B certified peripherals for EMC compliance.

Caution and Operation Conditions

Unauthorized modifications void FCC authorization; device must accept interference.

Canadian Users Notice

Compliance statement for Class B digital apparatus in Canada (ICES-003).

Disposal of Waste Equipment

Acer P206H Specifications

General

Screen Size	20 inches
Resolution	1600 x 900
Panel Type	TN
Aspect Ratio	16:9
Brightness	250 cd/m²
Contrast Ratio	1000:1
Response Time	5 ms
Ports	VGA, DVI
Viewing Angle (Horizontal)	170°
Viewing Angle (Vertical)	160°