What to do if my Acer X1160' Projector shows no image?
If your Acer Projector is displaying no image, ensure the signal cable and source are working. If you connect multiple sources at the same time, use the “Source” button switch. Also, ensure all connectors are securely connected and aren’t broken. You may also need to check the Main Board, DMD Board, Color Wheel, DMD Chip, and Engine Module.
How to fix color abnormalities on Acer X1160'?
To address color abnormalities on your Acer Projector, first, perform a “Reset (All data)” of the OSD Menu. Also, try to adjust the Color Wheel Index. If the issue persists, check the Main Board, DMD Board, and Color Wheel.
What to do if Acer Projector remote control or control panel failed?
If the remote control on your Acer Projector fails, check the battery and the remote controller itself. Also, check the IR receiver, Main Board, and IR Board (for refresh models). If the control panel fails, check the Power Key and the Main Board.
How to fix image flicker on Acer Projector?
To fix image flicker on your Acer Projector, first, try performing a “Reset (All data)” of the OSD Menu. Also, ensure that the signal cables and source work as well. Check the Lamp Module, Color Wheel, DMD Board, and Main Board.
How to resolve poor uniformity or shadows on Acer X1160' Projector?
To resolve poor uniformity or shadows on your Acer Projector, ensure the projection screen is free of dirt and that the projection lens is clean. Also, ensure the Brightness is within spec. Check rod alignment and the Engine Module.
How to fix line bar or line defect on Acer Projector?
To fix line bar or line defects on your Acer Projector, check if the Main Board and the DMD Board are assembled properly. Also, check the Main Board, DMD Board, and DMD Chip.
How to resolve dead pixel or dust issues on Acer X1160'?
To address dead pixel or dust issues on your Acer Projector, ensure the projection screen is free of dirt and that the projection lens is clean. Also, clean the DMD Chip and Engine Module. Check the DMD Chip and Engine Module.
How to fix garbage image on Acer X1160' Projector?
To fix a garbage image on your Acer Projector, ensure that the signal cables and source work as well. Check the Main Board and DMD Board.
How to resolve function abnormalities on Acer X1160' Projector?
To resolve function abnormalities on your Acer Projector, perform a “Reset (All data)” of the OSD Menu. Also, check the Main Board and DMD Board.
Steps to connect a computer to the projector using VGA and power cables.
Instructions for turning on the projector and preparing for a presentation.
Steps to safely shut down the projector after use.
General| Number of colors | 16.78 million colors |
|---|---|
| Projection distance | 11.9 m |
| Vertical scan range | 50 - 85 Hz |
| Horizontal scan range | 31 - 69 kHz |
| Projection technology | DLP |
| Contrast ratio (typical) | 2000:1 |
| Screen size compatibility | 0.64 - 7.62 \ |
| Projector native resolution | SVGA (800x600) |
| Keystone correction, vertical | ±40 ° |
| Digital zoom | 2 x |
| Aspect ratio | 4:3, 16:9 |
| Power supply | 255 W |
| Dimensions (WxDxH) | 267 x 187 x 80 mm |
| Lamp type | P-VIP |
| Lamp power | 160 W |
| Light source type | Lamp |
| Service life of light source | 4000 h |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| S-Video inputs quantity | 1 |
| Noise level | 33 dB |
| Power consumption (standby) | 8 W |
Weight and Dimensions| Weight | 2300 g |
|---|
To Next Page
