ADC SL20 User Manual

SL20 / SL31 / SL50 / SL75
Installation/Operator Manual
WARNING: For your safety the
information in this manual must be
followed to minimize the risk of fire or
explosion and to prevent property
damage, personal injury or death.
— Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your
building.
• Clear the room, building or area of all
occupants.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
• If you cannot reach your gas supplier,
call the fire department.
— Installation and service must be
performed by a qualified installer, service
agency or the gas supplier.
AVERTISSEMENT: Assurez-vous de bien
suivre les instructions données dans cette
notice pour réduire au minimum le risque
d’incendie ou d’explosion ou pour éviter
tout dommage matériel, toute blessure ou
la mort.
— Ne pas entreposer ni utiliser d’essence
ni d’autres vapeurs ou liquides
inflammables à proximité de cet
appareil ou de tout autre appareil.
— QUE FAIRE SI VOUS SENTEZ UNE
ODEUR DE GAZ:
• Ne pas tenter d’allumer d’appareils.
• Ne touchez à aucun interrupteur. Ne
pas vous servir des téléphones se
trouvant dans le bâtiment.
• Évacuez la pièce, le bâtiment ou la
zone.
• Appelez immédiatement votre
fournisseur de gaz depuis un voisin.
Suivez les instructions du fournisseur.
• Si vous ne pouvez rejoindre le
fournisseur de gaz, appelez le service
des incendies.
— L’installation et l’entretien doivent être
assurés par un installateur ou un service
d’entretien qualifié ou par le fournisseur
de gaz.
ADC Part No. 113403-17
American Dryer Corporation
88 Currant Road
Fall River MA 02720-4781 USA
Telephone: +1 (508) 678-9000 / Fax: +1 (508) 678-9447
e-mail: techsupport@amdry.com
www.amdry.com

ADC SL20 Specifications

General

Brand	ADC
Model	SL20
Category	Dryer
Language	English

Summary

Safety Precautions

SL20 Specifications

SL31 Specifications

SL50 Specifications

SL75 Specifications

Installation Procedures

Location Requirements

Guidelines for selecting an appropriate installation site for the dryer.

Unpacking / Setting Up

Instructions for removing the dryer from packaging and initial setup.

Leveling Dryer

Steps to ensure the dryer is properly leveled for optimal performance.

Dryer Enclosure Requirements

Specifications for the space or cabinet where the dryer will be installed.

Fresh Air Supply Requirements

Exhaust Requirements

Electrical Information

Electrical Requirements

Details on the electrical connections and standards required for installation.

Electrical Service Specifications (Gas Models Only)

Electrical Service Specifications (Electric Models Only)

Electrical Grounding Instructions

Electrical Connections

Single-Phase (10) Wiring Connections / Hookup

How to connect single-phase power to the dryer.

Gas and Steam Models Only 120-240V Application with Neutral

Specific wiring for gas/steam models with 120-240V and neutral.

200-240V Application without Neutral

Wiring for 200-240V applications without a neutral connection.

Electrically Heated Models Only

Gas Information

Gas Specifications for Non-CE and Non-AGA Approved Dryers

Gas Specifications for CE Approved Dryers

Gas Specifications for AGA Approved Dryers (Australia)

Piping / Connections

TYPICAL L.P. GAS INSTALLATION

Diagram and notes for installing L.P. gas piping.

TYPICAL NATURAL GAS INSTALLATION

Diagram and notes for installing natural gas piping.

Converting from One Family of Gas to Another

Conversion from Natural Gas to Propane or Butane Gas

Steps for converting the dryer from natural gas to propane or butane.

Non-CE Dryers

Specific instructions for non-CE dryers during gas conversion.

CE Dryers

Specific instructions for CE dryers during gas conversion.

Regulated Gas Valve

Conversion from Propane or Butane Gas to Natural Gas

Steps for converting the dryer from propane/butane to natural gas.

Gas Pressure Adjustment

Procedures for adjusting the gas valve pressure for proper operation.

Gas Pressure Testing

Steam Information

Steam Coil pH Level

Importance of maintaining specific pH levels for steam coil longevity.

Steam Requirements – High Pressure

Water Information

Water Supply

Requirements for the water supply to the dryer's fire suppression system.

Water Connections

Details on connecting the water supply to the dryer.

Preoperational Test

Gas Dryers

Preoperational checks specific to gas-powered dryers.

Electrical Dryers

Preoperational checks for electrically heated dryers.

Safety Related Circuits

Checking the proper function of safety circuits.

Tumbler Coating

Procedure to remove protective coating from the tumbler.

Microprocessor Programs / Selections

Information on factory preprogrammed dryer settings.

Preoperational Instructions

Coin Models

Instructions for programming coin-operated dryer models.

Non-Coin Models

Instructions for programming non-coin activated dryer models.

Shutdown Instructions

Service / Parts Information

Service

Guidance on who should perform service and how to contact support.

Parts

Information on obtaining replacement parts from the reseller or factory.

Warranty Information

Returning Warranty Cards

Instructions for completing and returning warranty cards.

Warranty

How to obtain a copy of the commercial warranty for the dryer.

Returning Warranty Parts

Routine Maintenance

Cleaning

Schedule and procedures for regular cleaning to ensure efficient operation.

Suggested Cleaning Schedule

Recommended cleaning frequency for lint screen and other areas.

Steam Dryers

Specific cleaning instructions for steam dryer components.

7 Days After Installation and Every 12 Months Thereafter

Schedule for professional inspection of dryer components and safety devices.

Data Label Information

Programming

Coin Models

Instructions for programming coin-operated dryer models.

Non-Coin Models

Instructions for programming non-coin activated dryer models.

Event Codes Defined: Top Pocket / Bottom

Explanation of error codes related to the top/bottom pocket.

Factory Settings Definitions

Definitions of factory-set parameters for dryer operation.