ADEMCO N7227V5 - Installation Instructions Manual

To Next Page

VISTA-10

N7227V5 5/97

Installation Instructions • Installation Instructions • Installation Instructions

Security System

THIS ISSUE INCLUDES THE NEW “QED” (QUICK ENROLLMENT

OF DEVICES) PROCEDURE FOR 5800 SERIES TRANSMITTERS

Main Page

Default Chapter2
- Recommendations for Proper Protection2
- Table of Contents3
- How to Use this Manual7
- Conventions Used in this Manual8
Section 1. GENERAL DESCRIPTION9
Figure 1. Installing the Cabinet Lock11
Section 2. INSTALLING the CONTROL11
- Installing the Control's Circuit Board Alone or (if Used), with a 4204 Relay Unit11
- Installing the Lock (if Used)11
- Mounting the Cabinet11
- Figure 2. Installing the PC Board Alone, or (if Used), with a 4204 Relay Unit12
- Installing Control and RF Receiver Circuit Boards Together in the Cabinet13
- Standard Phone Line Connections13
Section 3. INSTALLING REMOTE KEYPADS15
- Keypads that May be Used15
- Wiring to the Keypads15
  - Wiring Run Chart for Devices Drawing aux Power from the Control15
- Figure 5. Keypad Connections to the Control Board16
- Mounting the Keypads16
- Using a Supplementary Power Supply to Power Additional Keypads16
- Figure 6. Using a Supplementary Power Supply for Keypads17
- Preliminary Check-Out Procedure17
- Figure 7. 4-Wire Smoke Detector Connections to Zone 518
- Compatible 4-Wire Smoke/Combustion Detectors19
- Programming Hard-Wired Zones19
  - Programming Panic Keys20
- Check-Out Procedure for Hard-Wired Zones 1-621
  - Ready to Arm21
  - Section 5. WIRELESS (RF) ZONE EXPANSION (5700 & 5800 RF SYSTEMS)22
Basic Hard-Wired Zones 1-618
- Installing the Hard-Wired Zones18
  - Common Characteristics for Zones 1-618
- Wiring Burglary and Panic Devices to Zones 1-618
- Wiring 4-Wire Smoke/Combustion Detectors on Zones 518
Wireless (Rf) Zone Expansion (5700 & 5800 Rf Systems)22
- Wireless System Operation and Transmitter Supervision22
  - Transmitter Battery Life23
- Wireless Systems Available22
- Installation and Setup of the 4281/5881 Series Wireless Receivers23
- Receiver Supervision23
- 5700 Series Transmitter Setup24
- Figure 8. 4281, 5881, and 5882 Wireless Receivers (Cover Removed)24
- Installing the 5800TM Module24
- Setting the DIP Switches on 5700 Series Wireless Transmitters25
- Wireless Zone/ID Assignments for 5700 Series Transmitters25
- DIP Switch Tables for 5700 RF System Wireless Devices26
- Compatible 5700 Series Transmitters27
- Programming the Control for a 5700 Wireless System28
  - Rf House ID Code)28
  - Using the House ID Sniffer Mode (5700 Systems)28
- Zone Programming for 5700 Series Transmitters28
  - Go/Nogo Test30
- 5800 Series Transmitter Setup31
  - 5800 Series Transmitter Input Loops31
  - 5800 Series Transmitter Input Types31
- Compatible 5800 Series Transmitters32
- Programming the RF Transmitters (5800 RF Systems)33
- Enrolling 5800 Transmitters into the System34
  - Enrolling through Zone Programming ( 56)34
- Check-Out Procedure for Wireless Zones37
  - Transmitter ID Sniffer Mode (5700 RF Systems Only)37
  - Go/No Go Test Mode (5700 and 5800 RF Systems)37
- Deleting a Transmitter Serial Number from a Zone in 56 Mode (5800 System)37
- To Either Temporarily or Permanently Remove a Zone from the System (5800 System)37
- Section 6. RELAY OUTPUT DEVICES39
  - 4204 Relay Modules39
    - 4204 Setup39
    - Supervision39
  - Figure 9. 4204 Connections to Control39
  - Programming Options Defined39
  - Relay Device Basics39
  - Programming Output Relays41
    - Example of Output Relay Programming43
4285 Phone Module44
- Installing the Phone Module44
- Figure 10. 4285 Phone Module Wiring Connections46
- Programming the Control for Phone Access47
- Checking the Operation of the 4285 Phone Module48
Section 8. EXTERNAL SOUNDERS49
- Compatible Sounders49
- Figure 11. Typical Sounder Wiring50
- Programming for External Sounders50
- Sounder Connections50
- Testing the Sounder50
  - Control Board50
  - Alarm Output50
- Figure 12. Long Range Radio Connections51
- Programming for Long Range Radio51
Section 9. LONG RANGE RADIO51
- General Information51
- Connection51
- Control Terminals51
Audio Alarm Verification (Aav) Unit52
- General Information52
- Wiring Connections52
- Programming52
Figure 13. Connection of AAV Unit When Not Using a 4285 Phone Module53
Figure 14. Connection of AAV Unit When also Using a 4285 Phone Module53
Section 11. FINAL POWER up54
- Earth Ground Connections54
- AC Power-Up54
- Connecting the Back-Up Battery54
  - Calculating the Battery Size Needed54
  - Making the Battery Connections55
- Auxiliary Device Current Draw Worksheet55
- Section 12. ALPHA DESCRIPTOR PROGRAMMING56
Alpha Descriptor Programming56
- Assigning Zone Descriptors56
  - Entering Zone Descriptors (in Program Menu Mode 82)56
  - Programming the Descriptors56
- Alternate Method for Programming Zone Descriptors58
- Adding Custom Words59
- Alpha Vocabulary List (for Entering Zone Descriptors)60
- Character (ASCII) Chart60
Sequential Mode61
- (For 5800 Series Wireless Transmitters)61
Section 14. SYSTEM COMMUNICATION64
- Report Code Formats64
  - Table of Contact ID Event Codes66
  - Communication Programming66
    - Sescoa/Radionics Select68
    - Test Report Code69
Section 15. TESTING the SYSTEM71
- Test Procedure71
  - Transmitter Sniffer Mode72
  - Go/No Go Test Mode72
- To the Installer72
Section 16. SYSTEM OPERATION73
- Security Codes73
Section 17. TROUBLESHOOTING GUIDE77
- Contacting Technical Support79
Section 18. SPECIFICATIONS & ACCESSORIES80
- Specifications80
  - Formats Supported80
  - Remote Keypad80
- Accessories (Compatible Devices)82
- Regulatory Agency Statements83
  - Recommended Battery84
  - Canadian Department of Communications (Doc) Statement85
- Limitations of this Alarm System86
- Summary of Connections Diagram88
- Limited Warranty88

ADEMCO N7227V5 - Installation Instructions Manual

Table of Contents

Other manuals for ADEMCO N7227V5

Related product manuals