ADEMCO VIA-30PSE User Manual (English)

Other manuals for ADEMCO VIA-30PSE

Quick Guide4 pages

Installation Instructions104 pages

Questions and Answers:

P
Patricia CruzSep 1, 2025
Why am I getting a repeated low battery signal from my ADEMCO Security System?
- S
  Sarah PerezSep 1, 2025
  A repeated low battery signal from your ADEMCO Security System can be due to several reasons. The transmitter might be located in an area where the temperature drops below 32°F; if so, change its location and use magnetic contacts to protect the opening. It could also be due to a poor-quality or unspecified battery; check the battery and use only those specified in the instructions (this does not apply to transmitters with non-replaceable batteries). Finally, the transmitter itself might be malfunctioning; in this case, replace the faulty transmitter.
B
Brittany LopezAug 30, 2025
What to do if ADEMCO Security System does not arm properly?
- C
  Crystal NielsenAug 31, 2025
  If your ADEMCO Security System doesn't arm properly, it might be because the READY light is not on. Check for faulted zones by pressing [,]; make sure these zones are intact, or use Bypass arming if you prefer.
S
Stacey BrooksAug 29, 2025
Why is my ADEMCO Security System keypad beeping periodically?
- L
  Lauren JacksonAug 29, 2025
  Periodic beeping from your ADEMCO Security System keypad can indicate several issues. It might mean the system is in TEST mode, which can be resolved by entering "Code" + OFF. It could also signal a low battery in a wireless transmitter (displayed on the keypad); in this case, enter "Code" + OFF and replace the battery. Finally, it may indicate a supervision CHECK; inspect the wireless transmitter and restore communication to the RF receiver.
S
Sherry GonzalezAug 28, 2025
How to fix 'POWER' light off or 'NO AC' displayed on ADEMCO Security System?
- J
  josewardAug 28, 2025
  If the "POWER" light is off or “NO AC” is displayed on your ADEMCO Security System, the AC power supply may be interrupted. Check the transformer connection and the power line circuit breaker.
C
cbrownAug 27, 2025
Why does my ADEMCO Security System keypad show a low battery message?
- L
  Lisa BlackwellAug 27, 2025
  The "Bat" or “System Lo Bat” message (without zone numbers) indicates the system battery is low or missing. If you see "Bat" or “Lo Bat” + "00", the remote RF keypad battery is low. If the message is "Bat" or “Lo Bat” + "nn", it means the transmitter for zone “nn” has a low battery. Replace the corresponding battery to resolve the issue.
J
Jason BurchAug 27, 2025
Why am I getting a repeated low battery signal on my ADEMCO VIA-30PSE?
- L
  Luis LopezAug 27, 2025
  If you're getting a repeated low battery signal from your ADEMCO Security System, it could be due to a few reasons. The transmitter might be located in an area where the temperature drops below 32°F; if so, change its location or use magnetic contacts to protect the opening. It could also be due to a poor-quality or unspecified battery in the transmitter; check the battery and use only the types specified in the instructions. Finally, the transmitter itself might be malfunctioning, in which case you should replace it.
D
derrick72Aug 25, 2025
How to fix "POWER" light off or “NO AC” displayed on ADEMCO VIA-30PSE Security System?
- D
  David AdamsAug 26, 2025
  If the "POWER" light is off or “NO AC” is displayed on your ADEMCO Security System, it indicates an interrupted AC power supply. Check the transformer connection and the power line circuit breaker.
U
ubradyAug 25, 2025
Why is my ADEMCO VIA-30PSE keypad beeping?
- J
  Javier SilvaAug 25, 2025
  If your ADEMCO Security System keypad is beeping periodically, it could be due to several reasons. The system might be in TEST mode, which can be exited by entering "Code" + OFF. Alternatively, a wireless transmitter might have a low battery, indicated on the display; after replacing the battery, enter "Code" + OFF. Finally, a supervision CHECK may have occurred; check the indicated wireless transmitter and restore communication to the RF receiver to cancel the condition.

ADEMCO VIA-30PSE Specifications

General

Power Supply	Transformer
Power Supply Voltage	16.5 VAC
Input Voltage	120 VAC
Output Voltage	12 VDC
Zones	8
Battery Backup	Yes
Operating Temperature	0°C to 49°C (32°F to 120°F)
Humidity	Up to 85% non-condensing