Need help?Do you have a question about the ADJ VIZI BEAM RXONE and is the answer not in the manual?
Instructions for checking the shipping carton and inspecting the fixture for damage upon arrival.
Describes the Vizi Beam RXONE as a DMX intelligent moving head fixture with multiple operating modes.
Provides contact information and hours for ADJ Products, LLC customer support for assistance.
Information and warnings regarding lamp replacement for older software versions.
Guidance on lamp replacement warnings and procedures for newer software versions.
Information about the fixture's auto-sensing voltage and electronic ballast.
Explanation of the DMX protocol for lighting control.
How to connect multiple fixtures in a DMX chain for controller operation.
Specifications for DMX cables needed for control and primary/secondary operation.
Importance of using a terminator on long DMX cable runs to prevent erratic behavior.
Details on using 5-pin DMX connectors and conversion to 3-pin.
How to set the DMX starting address for fixture control.
How to select between 15-channel and 17-channel DMX modes.
How to select and activate built-in factory shows.
How to configure units for primary/secondary operation.
Defines fixture behavior when DMX signal is lost or interrupted.
How to activate or deactivate sound active mode for the unit.
How to adjust the sensitivity level for sound active mode.
How to invert the pan movement direction.
How to invert the tilt movement direction.
How to control the backlight on the unit's display.
How to run a self-test program for the fixture.
How to view and reset the installed lamp's running time.
How to enable automatic lamp activation upon power application.
How to manually switch the lamp power on or off.
How to display the current firmware/software version of the unit.
How to reset the fixture to its original factory settings.
How to reset the fixture's motors.
Adjusts the home position for the pan movement.
Adjusts the home position for the tilt movement.
Adjusts the shutter or dimmer setting.
Adjusts settings for the color wheel.
Adjusts settings for the gobo wheel.
Adjusts settings for the prism.
How to run the unit in sound-activated mode to music.
How to run pre-programmed shows on the fixture.
How to link multiple units for synchronized operation without a controller.
Instructions for safely replacing the unit's fuse.
Important precautions and steps before replacing the fixture's lamp.
Instructions for checking the shipping carton and inspecting the fixture for damage upon arrival.
Describes the Vizi Beam RXONE as a DMX intelligent moving head fixture with multiple operating modes.
Provides contact information and hours for ADJ Products, LLC customer support for assistance.
Information and warnings regarding lamp replacement for older software versions.
Guidance on lamp replacement warnings and procedures for newer software versions.
Information about the fixture's auto-sensing voltage and electronic ballast.
Explanation of the DMX protocol for lighting control.
How to connect multiple fixtures in a DMX chain for controller operation.
Specifications for DMX cables needed for control and primary/secondary operation.
Importance of using a terminator on long DMX cable runs to prevent erratic behavior.
Details on using 5-pin DMX connectors and conversion to 3-pin.
How to set the DMX starting address for fixture control.
How to select between 15-channel and 17-channel DMX modes.
How to select and activate built-in factory shows.
How to configure units for primary/secondary operation.
Defines fixture behavior when DMX signal is lost or interrupted.
How to activate or deactivate sound active mode for the unit.
How to adjust the sensitivity level for sound active mode.
How to invert the pan movement direction.
How to invert the tilt movement direction.
How to control the backlight on the unit's display.
How to run a self-test program for the fixture.
How to view and reset the installed lamp's running time.
How to enable automatic lamp activation upon power application.
How to manually switch the lamp power on or off.
How to display the current firmware/software version of the unit.
How to reset the fixture to its original factory settings.
How to reset the fixture's motors.
Adjusts the home position for the pan movement.
Adjusts the home position for the tilt movement.
Adjusts the shutter or dimmer setting.
Adjusts settings for the color wheel.
Adjusts settings for the gobo wheel.
Adjusts settings for the prism.
How to run the unit in sound-activated mode to music.
How to run pre-programmed shows on the fixture.
How to link multiple units for synchronized operation without a controller.
Instructions for safely replacing the unit's fuse.
Important precautions and steps before replacing the fixture's lamp.
Power| voltage | 100~240V, 50/60Hz |
|---|---|
| power consumption | 199W |
| fuse | 5A |
Lighting and Optics| lamp | Osram® Siruius HRI 100W 1R |
|---|---|
| color temperature | 9000°K |
| light output | 99250 LUX @ 10M, 70030 LUX @ 15M |
Weight and Dimensions| weight | 51 Lbs. / 23 kgs. |
|---|---|
| dimensions (inches) | 12.75”(L) x 14.5”(W) x 22.5”(H) |
| dimensions (mm) | 279mm x 225mm x 387mm |
To Next Page
