Agilent Technologies 4395A - Page 202

Calibration
Required
for
the Impedance
Analyzer Mode
Step
2: Specifying
Parameter
V
alues
In
this step
,
you
specify
2
parameters
for
each
of
the
OPEN,
SHORT
, and
LOAD
circuit states;
thus
6 parameters
in
all.
While
the
parameters
for
OPEN
and
SHORT
are
required,
those for
LO
AD are
optional.
T
o specify
the
parameter
values
,
do
the
following:
1.
Choose
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
OPEN: CONDUCT(G)
,and
enter
the
conductance
value
(G)
for
OPEN.
2.
Choose
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
NN
N
N
N
CAP.
(C)
,
and
enter
the
capacitance
value
(C)
for
OPEN.
3.
Choose
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
SHORT:
RESIST.
(R)
,
and
enter
the
resistance
value
(R) for
SHORT.
4.
Choose
N
N
N
NN
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
N
INDUCT.
(L)
,
and enter
the inductance
value (L)
for
SHORT
.
5.
Choose
N
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
LOAD:
RESIST.
(R)
,
and
enter
the
resistance
value
(R)
for
LO
AD
.
6.
Choose
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
INDUCT.
(L)
,
and
enter
the
reactance
value
(L)
for
LO
AD
.
7.
Choose
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
N
N
N
N
N
N
N
N
N
N
N
STD
DONE
(DEFINED)
.
Step
3:
Specifying
the
Standard
Label
1.
Choose
N
N
NN
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
LABEL
KIT .
2.
Enter
the
standard
label
(up
to
10
characters).
3.
Choose
N
N
N
N
N
N
N
NN
N
N
N
N
N
DONE
.
4.
Choose
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
KIT
DONE
(MODIFIED)
.
7-20 Calibration