Agilent Technologies HP 83711B Calibration Guide

lb Set Up the Spectrum Analyzer and Carrier Noise Test Set
.........
lb Calibrate the System
..........................
lb Phase Lock the Sources
.........................
‘I% Measure Phase Noise at 100 Hz, 1 kHz, and 10 kHz Offsets
........
lb Calculate Phase Noise for a Dynamic Siiai Analyzer
...........
‘IbMeasurePhaseNoiseatlOOkHzOffset.
.................
lb Calculate Phase Noise for an Analog Spectrum Analyzer
..........
‘Ib Check Single-Sideband Phase Noise at 10 GHz
..............
Dynamic Signal Analyzer Phase Noise Calculation
.............
Spectrum Analyzer Phase Noise Calculation:
................
‘Ib Check Single-Sideband Phase Noise at 18 GHz
..............
Dynamic SiiaI Analyzer Phase Noise Calculation
.............
Spectrum Analyzer Phase Noise Calculation
................
‘Ib Check Single-Sideband Phase Noise at 500 MHz (HP 83712A/12B,
HP 83732A/32B only)
..........................
Dynamic SiiaI Analyzer Phase Noise Calculation
.............
Spectrum Analyzer Phase Noise Calculation
................
If the Procedure F’aiIs
...........................
Non-HarmonicSpuriousSii3kHzto30kHz
................
Recommended Equipment
.........................
ToSetUptheEquipmentfor17.005111GHz
................
‘Ib Calibrate the System
..........................
‘IbPhaseLocktheSources
.........................
lb Measure Spurious Response at 17.005111 GHz
..............
lb Calculate Actual Spurious SiiaI Level
..................
‘Ib Set Up and Calibrate the System for 17.501777 GHz
............
‘IbPhaseLocktheSources
.........................
‘Ib Measure Spurious Response at 17.501777 GHz
..............
IftheProcedureFXIs
...........................
Non-Harmonic Spurious Signals >30 kHz
...................
Recommended Equipment
.........................
‘IbSetUptheEquipment.
.........................
lbCheckforSpursfromlto20GHz
....................
‘Ib Check Spurs from 0.01 to 1 GHz (HP 83712A/12B, HP 83732A/32B only) . .
If the Procedure PaiIs
...........................
PuIse On/Off Ratio (HP 83731A/31B and HP 83732A/32B only)
.........
Recommended Equipment
.........................
‘IbSetUptheEquipment.
.........................
‘IbMeasurePuIseModuIationOn/OffRatio.
.................
If the Procedure Fails
...........................
Pulse Rise/Fall Thne (HP 83731A/31B and HP 83732A/32B only)
........
Recommended Equipment
.........................
‘IbSetUptheEquipment.
.........................
‘IbMeasureRiseTime
...........................
lbMeasureF%IITime.
...........................
RI Measure Rii/FaII Time for 0.01 to 1 GHz (HP 83732A/32B)
........
If the Procedure F’aiIs
...........................
pulse Width (HP 83731A/31B and HP 83732A/32B only)
............
Recommended Equipment
.........................
‘IbSetUptheEquipment.
.........................
To Measure pulse Width
..........................
‘RI Measure Pulse Width for 0.01 to 1 GHz (HP 83732A/32B)
.........
IftheProcedurePaiIs
...........................
Maxhnm PM Deviation (HP 83731A/31B and HP 83732A/32B, only)
......
Recommended Equipment
.........................
3-34
3-34
3-34
3-34
3-35
3-35
3-36
3-36
3-36
3-36
3-37
3-37
3-37
3-37
3-37
3-37
3-38
3-39
3-39
3-40
340
3-40
3-41
3-41
3-42
342
3-42
3-43
344
3-44
3-44
3-45
3-45
346
3-47
3-47
3-47
3-48
348
349
349
3-49
3-50
3-51
3-51
3-51
3-52
3-52
3-52
3-53
3-53
3-54
3-55
3-55
COlltOlltO-3

Agilent Technologies HP 83711B Specifications

General

Brand	Agilent Technologies
Model	HP 83711B
Category	Test Equipment
Language	English