To Next PageTo Next Page
Need help?Do you have a question about the Agilent Technologies HP 83711A and is the answer not in the manual?
General| Brand | Agilent Technologies |
|---|---|
| Model | HP 83711A |
| Category | Test Equipment |
| Language | English |
Procedures for inspecting, installing, and powering up the synthesizer.
Instructions for carefully removing and inspecting synthesizer contents.
General procedure for installing and initial power-up of the synthesizer.
Procedure to activate and perform the synthesizer's self-test function.
Troubleshooting common problems encountered during setup or operation.
Guidance on resolving issues related to synthesizer power-up.
Steps to take when the synthesizer's self-test fails.
How to input parameter values using the numeric keypad and terminator keys.
Using the front panel knob to adjust parameter values and cursor position.
Using arrow keys to increment or decrement parameter values and change increment step.
Procedure for saving and recalling instrument states to/from memory registers.
How to view and clear error messages from the synthesizer's error queue.
Procedure for changing the synthesizer's default HP-IB address.
Troubleshooting common data entry and programming issues.
Guidance on resolving issues when the synthesizer does not respond to programming commands.
Steps to generate a continuous wave (CW) signal with specific frequency and power.
Using external equipment to generate millimeter-wave signals.
Procedure for setting up and using external diode detector leveling.
Procedure for setting up and using an external power meter for leveling.
Steps for performing the level correct routine to calibrate output power.
Procedure for recalling and using stored level correction data.
Explanation of annunciator states and troubleshooting common issues.
Troubleshooting issues related to the RF output signal.
Detailed performance specifications for the HP 83711A/11B synthesizer.
Specifications related to the RF output power and level.
Specifications for accuracy and flatness of the output signal.
Specifications for SSB phase noise and harmonic content.
Detailed performance specifications for the HP 83712A/12B synthesizer.
General specifications including programming, environmental, and noise emission.
Description of the connectors located on the synthesizer's front panel.
Description of the front panel annunciator indicators and their meanings.
Overview of synthesizer connectors on the front and rear panels.
Details on the BNC and Type-N coaxial connectors and their uses.
Information on the HP-IB interface connector and available cables.
Description of the synthesizer's main display and annunciators.
Explanation of how to use the front panel knob for data entry and adjustment.
Information on the synthesizer's power switch operation.
Details on the different types of power cables supplied and their part numbers.
Key function for moving the cursor to the right digit.
Function to invoke and change the synthesizer's HP-IB address.
Key used to terminate parameter entries and confirm values.
Enables external diode detector leveling for power control.
Key used to set and modify the synthesizer's output frequency.
Enables internal leveling for automatic ALC control.
Function to calibrate external path losses and create a level correction table.
Function to set the frequency multiplier for extended frequency ranges.
Key used to set the synthesizer's output power level.
Resets the synthesizer to a known, predefined state.
Recalls a previously stored instrument state from a register.
Activates the alternate function of any key pressed directly after it.
Initiates activation of special functions.
Enables changing the increment value for parameters.
Function to toggle the attenuator hold between locked and unlocked states.
Turns off the synthesizer's fluorescent display and LED annunciators.
Clears application-specific information from synthesizer memory.
Changes the HP-IB address for external power meter communication.
Selects the programming language for power meter communication.
Allows manual selection between SCPI or HP 8673 compatible language.
Initiates the synthesizer's functional verification (self-test).
Lists and describes special service routines accessible via function numbers.
Displays software version and instrument serial number.
Lists all error messages with their codes, descriptions, and action required.
Detailed explanations of specific error codes and their causes.
Explanation of safety symbols used in the documentation and on the product.
Definition of miscellaneous symbols like CE and CSA.
Important safety information and precautions before operating the product.
Instructions for cleaning the synthesizer cabinet.
Company certification regarding product specifications and calibration traceability.
Details of the Hewlett-Packard instrument warranty, including terms and conditions.
Defines the limitations of the product warranty and disclaims implied warranties.
States the buyer's sole remedies and limits HP's liability.
Information on obtaining product maintenance and customer assistance.
