To Next PageTo Next Page
Need help?Do you have a question about the Agilent Technologies 8960 Series and is the answer not in the manual?
General| Brand | Agilent Technologies |
|---|---|
| Model | 8960 Series |
| Category | Test Equipment |
| Language | English |
General safety precautions for instrument operation, including Class 1 LEDs and compliance with standards.
Guidelines for operating the instrument in specific environmental conditions like humidity and altitude.
Pre-operation checks including voltage, fuse, and safety precautions.
Instructions for grounding the instrument to prevent shock hazards.
Guidance on using the correct fuse type and avoiding repaired fuses.
Prohibition of operating the instrument in the presence of flammable gases.
Warning against removing covers and emphasizing qualified personnel for repairs.
Explains the meaning of WARNING and CAUTION signs in the manual.
Details on CE and CSA marks indicating compliance and registration.
Agilent's certification of product specifications and traceability of calibration measurements.
Agilent Technologies warranty for hardware and software, including terms and conditions.
Information on obtaining product maintenance and customer support.
Details on how to contact Agilent service centers and representatives globally.
Contact details for Agilent's sales offices in various regions worldwide.
Declaration of product conformity with European directives and product standards.
Manufacturer's declaration regarding product sound pressure emission levels.
Steps to establish a call and select measurements for AMPS/136.
Procedures to select and set up measurements for AMPS/136.
Steps to disable or turn off an active measurement.
How to modify call parameters for the AMPS/136 application.
Procedures for modifying cell identification and handoff information.
How to adjust the mobile station's transmit power level.
Steps to execute a mobile station handoff procedure.
Steps to configure instrument settings and system parameters.
Procedure to terminate an active call connection.
How to measure the transmit power of a mobile on a digital traffic channel.
Procedure to assess the modulation accuracy of a mobile.
Steps to measure power levels in adjacent channels.
How to perform bit error ratio measurements in DTC Test mode.
Procedure for measuring IQ tuning with specific transmission patterns.
How to measure transmit power on an analog voice channel.
Procedure to measure the frequency stability of a mobile.
Steps to measure frequency modulation characteristics.
Steps to establish a call and select measurements for cdma2000.
Procedures to select and configure measurement parameters for cdma2000.
Steps to disable or turn off active measurements.
Instructions for setting up IS-2000 and IS-95 calls.
How to modify call parameters in the cdma2000 application.
Procedures for setting cell parameters, access, and registration.
How to adjust code channel levels for cdma2000.
Steps to execute a handoff procedure in cdma2000.
Steps to configure instrument and system settings for cdma2000.
Procedure to terminate a call connection.
How to measure waveform quality, including rho and other parameters.
Procedure for measuring waveform quality during handoff.
Steps to measure the average power of a digital signal.
How to measure channel power.
Procedure to measure access probe power.
How to measure frame error rate.
Procedure for measuring TDSO Frame Error Rate.
How to measure code domain power and noise.
Procedure to measure code channel time and phase error.
How to measure gated power.
Procedure to measure spurious emissions.
Steps to establish a data connection and select GPRS measurements.
Procedures to select and configure measurement parameters for GPRS.
Steps to disable or turn off active measurements.
How to modify call parameters for GPRS.
Procedures for setting cell parameters in GPRS.
Steps to execute a handover procedure in GPRS.
How to adjust the mobile station's transmit power level in GPRS.
Steps to configure instrument and system settings for GPRS.
Procedure to terminate a GPRS data connection.
How to measure transmit power for GPRS.
Procedure to measure power over time for GPRS.
How to measure phase and frequency error for GPRS.
Procedure to measure output RF spectrum for GPRS.
How to measure bit error rate for GPRS.
Steps to establish a call and select GSM measurements.
How to choose measurements from the selection screen.
Procedures to select and configure measurement parameters for GSM.
Steps to disable or turn off active measurements.
How to modify call parameters for GSM.
Procedures for setting cell parameters in GSM.
Steps to configure instrument and system settings for GSM.
Procedure to terminate a call connection in GSM.
How to measure transmit power for GSM.
Procedure to measure power over time for GSM.
How to measure phase and frequency error for GSM.
Procedure to measure fast bit error rate for GSM.
How to measure bit error rate for GSM.
Procedure to measure output RF spectrum for GSM.
How to measure IQ tuning for GSM.
Procedures to choose and switch between different test application formats.
Steps to select and switch between different test applications on the instrument.
