Airflow Ceiling fans User Manual

1
BUILDER’S CHOICE
™
GALLERY EDITION
CIRCUIT BREAKER
(TRIP BREAKER FOR THE
CIRCUIT YOU WILL BE
WORKING ON)
FUSE BOX
(REMOVE FUSE FOR THE
CIRCUIT YOU WILL BE
WORKING ON)
• The blades in each pack are matched for equal
weight to assure smooth fan operation. If
more than one fan is being installed, be
careful not to mix blades from different
cartons.
• Inspect the contents of your carton for
possible shipping or handling damage and
report any such damage directly to your
authorized Airflow dealer.
• It is always a good idea to have an assistant
to help with the installation.
• When cleaning, painting, or working near
your fan, be very careful of the fan and blades.
Always turn the power OFF to the ceiling fan
before servicing it, working on it, or replacing
light bulbs.
• Never insert anything into the path of the
fan blades while the fan is in operation.
• Never install a fan over a pool or spa.
• Never operate a fan that has been damaged
in any way. Contact Airflow by calling toll-
free 1-888-227-2178, or contact your local
authorized Airflow dealer for assistance in
obtaining service.
CONTENTS
READ AND SAVE THESE INSTRUCTIONS
• All wiring must be in accordance with the National Electric Code ANSI/NFPA 70-1993 and the appropriate local electrical
codes. The National Electric Code requires proper grounding as a precaution against electrical shock. A qualified electri-
cian should be consulted if you are unsure.
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for ceiling fan
installations, if it is not, a new box must be installed. Airflow extension poles are available for sloped or high ceiling
installations.
• This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The maximum
current requirement for the fan with light fixture is 3.8 amps. The fan uses about 1 amp or 100 watts. Maximum light
current is 2.8 amps or 340 watts of lighting.
• Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make
sure all wires are within the canopy and that no wires are being pinched.
For best performance and for your warranty to be valid,
use only genuine Airflow blades, light fixtures, and accessories.
SAFE USE
Safety and the proper operation of your Airflow fan both require a thorough knowledge of the product and
proper installation; therefore, before attempting to install and operate your Airflow fan, read this owner’s
manual completely and carefully. Retain this manual for future reference.
SAFETY FIRST
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
MOUNTING RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
GETTING STARTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
FAN INSTALLATION (USA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
LIGHT FIXTURE INSTALLATION (USA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
CONTROL FEATURES: 3-SPEED OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
AUTHORIZED SERVICE CENTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
PRODUCT SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
BEFORE YOU START
P/N 8943500 AA0905
CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at
the circuit breaker or fuse box before attempting any installation procedure.
18"
84"
70"

Airflow Ceiling fans Specifications

General

Brand	Airflow
Model	Ceiling fans
Category	Fan
Language	English

Summary

Safety and Preparation

Safety First

Crucial safety information and warnings for fan installation and operation.

Electrical Shock Prevention

Ensure electricity is turned off at the circuit breaker or fuse box before installation.

Before You Start

Key preparation steps including wiring, outlet box, and electrical supply requirements.

Safe Use Guidelines

Follow safe use practices, including blade clearance and avoiding installation over pools.

Mounting Recommendations

Location Considerations

Guidance on choosing the best room location for fan installation, considering safety and clearance.

Fan Size Guidance

Recommendations for selecting the appropriate fan size based on room dimensions.

Sloped Ceiling Installations

Instructions and considerations for installing fans on sloped or cathedral ceilings.

Extension Pole Usage

Guidance on when and how to use extension poles for optimal fan placement.

Ceiling Angle Calculation

How to use the provided template to determine if a ceiling angle is suitable for installation.

Installation Steps and Wiring

Unpacking and Parts Check

Instructions for unpacking fan components and verifying all parts are present.

Fan Preparation

Steps for preparing the fan for installation, including downrod and ball assembly.

Ceiling Outlet Box Requirements

Ensuring the ceiling outlet box is approved and suitable for fan mounting.

Mounting Bracket Installation

Attaching the mounting bracket to the ceiling outlet box using provided hardware.

Hanging the Fan

Procedure for safely hanging the fan body onto the installed mounting bracket.

Electrical Connections

Step-by-step guide for making wire connections between the fan and the house wiring.

Canopy Hatch Installation

Tucking wires and securing the canopy to cover the mounting bracket and wiring.

Remove Shipping Blocks

Instructions for removing shipping blocks from the fan motor before blade installation.

Blade & Blade Holder Installation

Attaching the fan blades and blade holders to the motor assembly.

Light Fixture Installation

Connecting and installing the light kit fitter, bulbs, bowl, and pull chains.

Fan Operation and Troubleshooting

Control Features: 3-Speed Operation

Explanation of the pull-chain switches for fan speed and light control.

Troubleshooting Guide

Common problems and their possible remedies for fan operation issues.

Caring for Finishes

Recommendations for cleaning and maintaining fan finishes without damage.

Blade Care

Instructions for cleaning and polishing wood finish fan blades.

Never Lubricate This Fan

Warning against oiling the sealed bearings of the fan motor.

Changing Lightbulbs

Procedure for safely replacing lightbulbs and avoiding warranty voidance.

Service Centers and Specifications

Authorized Service Centers

List of authorized service centers by state and city for customer support.

Product Specifications

Detailed specifications for the fan, including dimensions, finishes, and motor details.