Aleko HTIO2BLD - User Manual

Questions and Answers

M
Michelle EvansAug 9, 2025
Why is my Aleko HTIO2BLD Hot Tub heating system not working?
- M
  michael45Aug 9, 2025
  If the heating system in your Aleko Hot Tub isn't working, first, make sure the temperature is set higher (68°F~104°F) than the current water temperature. Also, check the filter cartridge and clean or replace it if it's dirty. Ensure that the water levels are at the specified levels. If these steps don't resolve the issue, the heating element may have failed and further assistance may be needed.
R
Randy VegaAug 14, 2025
What to do if the Aleko Hot Tub display temperature is too high?
- T
  Tiffany JamesAug 14, 2025
  If the display temperature on your Aleko Hot Tub reads higher than 104°F, the HL code is displayed, and it's beeping after stopping the heating function, unplug it and wait 20 minutes for the temperature to reduce. Also, ensure that the water inlet through the filter system is not blocked and clean the inlet if necessary. If the problem persists, further assistance may be needed.
G
Gabriel FernandezAug 19, 2025
How to clean Aleko Hot Tub water?
- T
  Timothy RasmussenAug 20, 2025
  If your Aleko Hot Tub's water isn't clean, increase the filtration time. Also, clean or replace the filter cartridge. If the issue persists, refer to the chemical manufacturer’s instructions for proper water maintenance.
E
Elizabeth RoweAug 25, 2025
What to do if Aleko HTIO2BLD Hot Tub jet system does not operate?
- L
  Larry MorrisAug 25, 2025
  If the jet system on your Aleko Hot Tub isn't working, it could be that the air pump is too hot. Unplug the air pump and, after it has cooled down, plug it back in and press the Jet button to activate. If this does not solve the problem, further assistance may be needed.
J
Janet PayneAug 29, 2025
Why Aleko HTIO2BLD Hot Tub filtering system does not operate?
- J
  Jessica RileyAug 29, 2025
  If the filtering system on your Aleko Hot Tub isn't working, start by cleaning or replacing the filter cartridge. If that doesn't work, try loosening the filter slightly. Also, have a professional electrician check if the household input voltage or frequency is normal.
M
Marvin NashSep 3, 2025
What to do if my Aleko HTIO2BLD shows 'Dwerg not code'?
- C
  caitlincraneSep 4, 2025
  If your Aleko Hot Tub displays 'Dwerg not code', it might be due to insufficient power. First, check the power capabilities specified by the manufacturer. If the power is inadequate, you should inquire about the correct power requirements.

Summary

Introduction

Safety Warnings

Lists critical safety warnings related to electrical shock, children, water temperature, and usage.

Prior to Assembly

Ensure All Parts are Present

Assembly Instructions

Connect and Use Inflation Hose

Assembly & Operation Setup

Install Filter and Fill Water

Steps for installing the filter cartridge and filling the spa with water to the correct level.

Control Panel Overview

Explanation of the control panel buttons and their functions, including filter and bubble jets.

Spa Operation

Heater and Filter Operation

Details on operating the heating system and its interaction with the filter pump.

Setting Water Temperature

Water Maintenance

Maintaining Spa Water Quality

Filter Cartridge Care

Cleaning, Emptying, and Storage

Draining and Deflating the Spa

Troubleshooting and Error Codes

Common Problems and Solutions

Addresses common issues with probable causes and practical solutions for operation problems.

Control Panel Error Codes

Explains error codes displayed on the control panel and provides corresponding solutions.

Electrical Safety Zones

Grounding Requirements

Aleko HTIO2BLD Specifications

General

Model	HTIO2BLD
Category	Hot Tub
Type	Inflatable
Shape	Round
Height	28 inches
Water Capacity	210 gallons
Material	PVC
Temperature Range	68-104°F
Air Jets	130
Voltage	110-120V
Control System	Digital
Inflation Time	5-10 minutes
Heater	1200W
Included Accessories	Cover, repair kit

Related product manuals

Aleko Inflatable SPA

19 pages