Need help?Do you have a question about the ALLEN & HEATH ZED 16 FX and is the answer not in the manual?
General| Type | Analog Mixer |
|---|---|
| Channels | 16 |
| Mic Inputs | 8 |
| Line Inputs | 8 |
| Mono Channels | 8 |
| Stereo Channels | 4 |
| Mic Preamps | 8 |
| EQ (mono channels) | 3-band |
| EQ (stereo channels) | 2-band |
| Phantom Power | Yes |
| Aux Sends | 4 |
| FX Processor | Yes |
| Internal FX | 16 |
| USB Interface | Yes |
| USB Channels | 2 x 2 |
| Headphone Output | 1 |
| Monitor Outputs | Yes |
| Main Outputs | XLR |
Details the terms and conditions under which the product warranty is valid.
Instructions for replacing the mains plug and wiring colours.
General advice for preventing damage, handling, and environmental considerations.
Highlights the mixer's suitability for live sound, recording, and various venue types.
Details the design and performance of the high-gain, two-stage microphone and line pre-amplifiers.
Explains the 3-band EQ on mono and 2-band EQ on stereo channels.
Describes the four auxiliary buses for monitors and external effects.
Introduces the built-in professional quality effects processor with various algorithms.
Discusses the flexibility and variety of inputs available on mono and stereo channels.
Explains the easy integration of the mixer with computers via USB for audio transfer.
Provides input operating level specifications in dBu.
Specifies nominal and maximum output levels for various outputs.
Details the frequency response across different input types and outputs.
Presents Total Harmonic Distortion plus noise measurements for various signal paths.
Specifies analogue and USB headroom values.
Details the USB audio interface specifications including sample rate.
Lists noise figures for microphone pre-amps and mix outputs.
Provides physical dimensions of the ZED mixers in mm and inches.
Lists the unpacked and packed weights for each ZED mixer model.
Describes the standard 3-pin XLR input for microphones.
Details the 1/4" jack socket for line level signals, overriding the mic input.
Explains the 1/4" jack for unbalanced insert send/return signals.
Adjusts input amplifier gain for XLR and line inputs.
Reduces pop noise and rumble from microphone signals.
Details the High Frequency EQ with a 12kHz corner frequency.
Describes the Mid Frequency EQ with sweepable frequencies.
Explains the Low Frequency EQ with an 80Hz corner frequency.
Controls signal level to auxiliary buses 1 and 2, sourced pre-fade.
Controls signal level to auxiliary buses 3 and FX, sourced post-fade.
Adjusts signal balance between left and right stereo outputs.
Mutes the channel signal to main buses and auxiliary buses.
Pre-Fade Listen switch for monitoring and clipping indicator.
Controls the channel signal level to the main and auxiliary buses.
Additional unbalanced stereo input via phono connectors.
1/4" jack sockets for line level stereo signals.
Adjusts the level of the stereo return input.
Switches the stereo return signal on or off.
Selects routing for Stereo Return signal to LR bus or stereo channel.
Adjusts the input level for the ST1 stereo input.
Features a 2-band EQ for the stereo channel with 12kHz and 80Hz corner frequencies.
Configures Aux 1 & 2 as mono sends or a stereo send pair.
Controls signal level to Aux 1 & 2 buses, sourced pre-fade.
Controls signal level to Aux 3 and FX buses, sourced post-fade.
Varies relative levels between left and right channels.
Mutes the channel signal to main LR and Aux buses.
Pre-Fade Listen switch and clipping indicator for stereo channels.
Controls the stereo channel signal level to main LR and Aux/FX buses.
Reference to ST1 description on previous pages.
Details ST2, noting its difference in additional stereo input labelling.
Describes ST3, featuring USB audio input and phono record outputs.
Covers the FX channel and ST4 stereo input for external effects return.
Explains the USB type B connector and output routing selector switches.
LEDs indicate selected effects type and parameter adjustment.
Indicates when effects types 9-16 are selected.
Select effects type and adjust parameters when TAP is held.
Used for delay tempo or parameter adjustment.
Send effects output signal to Aux 1 & 2 buses.
Varies relative levels between left and right effects channels.
Mutes effects signals to main LR and Aux buses.
Pre-Fade Listen for effects and clipping indicator.
Controls the effects signal level to main LR and Aux 1 & 2 buses.
Lists and describes the 16 available effects presets.
Provides a table detailing effects, preset names, and parameter adjustments.
1/4" sockets for Aux 1 to 3 outputs (FX/Aux 4 internal).
1/4" sockets for unbalanced insert send/return signals.
Balanced XLR outputs for main left and right signals.
Mono sum of main left & right post-fade signals.
1/4" and 3.5mm sockets for stereo headphones.
1/4" jack for connecting a footswitch to mute effects.
Switches 48V phantom power to all mic XLR connectors.
12-segment LED meters for peak signal response.
Adjusts the level of the headphone signal.
Selects signal source for headphone monitor and meters.
Adjusts volume for the Alt Output, used for separate monitor speakers.
Selects signal source for the Alt output.
Adjusts the level of the Aux 1 and 2 outputs.
100mm faders for the main LR outputs.
Details the stereo bi-directional USB 1.1 compliant audio CODEC.
Notes on setting volume levels for XP/Vista systems.
Notes on setting volume levels for Windows 7 systems.
Introduction to the Cakewalk sequencing and recording software.
Lists key features of the SONAR X1 LE audio workstation.
Instructions for installing the SONAR LE software.
Steps for configuring SONAR LE with the ZED mixer for audio I/O.
Guide to setting up Pro Tools Aggregate I/O for ZED connectivity.
Diagrams and notes for creating insert cables.
Provides wiring details for MIC, TRS, and XLR cables.
Instructions and benefits for registering the mixer product.
To Next Page