Allen-Bradley 140G Series User Manual

Cu/CuAl Terminal lugs for 140G-M
Cu/CuAl Terminali anteriori per cavi
Cu/CuAl Vorderseitige Anschlüsse für Kabel
Cu/CuAl Prises de raccordement avant pour câbles
Cu/CuAl Terminales frontales para cables
Bul. 140G/140MG
DIR 1000479R0824 Version 04
WARNING: To prevent electrical shock, disconnect from power source before
installing or servicing. Install in suitable enclosure. Keep free from contaminants.
(Follow NFPA70E requirements).
AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o
manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem
passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden.
AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation
secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée.
Protéger le produit contre les environnements agressifs.
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o
del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes.
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a
instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de
contaminantes.
Installation - Installazione - Instalación
Instalação - -
DIR 1000479R0824 Version 04 - 140G-M-TLA23, 140G-M-TLA24, 140G-M-TLC23, 140G-M-TLC24, 140G-M-TLA33, 140G-M-TLA34, 140G-M-TLC33, 140G-M-TLC34,
3p
4p
CuAl
(2) 250...500 MCM
(2) 120...240 mm²
x3
x4
x3
x3
x4
x4
x6
x8
3p
4p
Cu
(2) 3/0...350 MCM
(2) 85...185 mm²
警告：感電事故防止のため、取付けまたは修理の際は電源から取り外してく
ださい。適切なケース内に取付けてください。また、汚染物質がないことを
確認してください。
警告：为了防止触电，在安装或维修之前必须先切断电源。安装在合适的设备
箱内。防止接触污染 。物
140G-M-TLA23
140G-M-TLA24
140G-M-TLC23
140G-M-TLC24
x3
x4
x3 x3
x4 x4
x6
x8
Screw Screw
Lug Screw Screw
LENGTH M
20 mm (0.79") M 6
LENGTH M
35 mm (1.38") M 6
LENGTH M
20 mm (0.79") M 6
LENGTH M
35 mm (1.38") M 6
140G-M-TLA2A3, 140G-M-TLA2A4
Lug
Required tools
xx lb-in
xx Nm
xx lb-in
xx Nm
xx lb-in
xx Nm
LENGTH dia.
0.28" (7mm) 0.1 9
LENGTH dia.
0.28" (7mm) 0.1 9

Allen-Bradley 140G Series Specifications

General

Series	140G
Poles	1, 2, 3, 4
Standards	UL 489, CSA C22.2 No. 5, IEC 60947-2
Type	Molded Case Circuit Breaker
Frame Sizes	G
Amperage	10A to 3000A
Trip Type	Thermal-Magnetic, Electronic
Mounting	Fixed or Plug-in
Voltage Ratings	Up to 690V AC

Summary

Cu/CuAl Terminal Lugs

Required Tools

Lists the necessary tools for installing terminal lugs.

CuAl Terminal Lug Specifications

Specifications for CuAl terminal lugs, including wire sizes and model numbers.

Cu Terminal Lug Specifications

Specifications for Cu terminal lugs, including wire sizes and model numbers.

Safety Instructions

Electrical Shock Hazard

Warning to disconnect power before installation or servicing to prevent electrical shock.

Additional Terminal Lug Specifications

CuAl Terminal Lugs (3-Wire)

Specifications for CuAl terminal lugs supporting 3-wire configurations.

Cu Terminal Lugs (3-Wire)

Specifications for Cu terminal lugs supporting 3-wire configurations.

CuAl Terminal Lugs (Ip20 Protection)

Specifications for CuAl terminal lugs with Ip20 protection.

Installation Example 140G-M-TLA23

Torque Specifications

Details torque values for various components during installation.

Wire Size Compatibility

Shows compatible stranded and flexible cable sizes for CuAl and Cu.

Installation Example 140G-M-TLA33

Component Assembly Steps

Illustrates the assembly steps for the 140G-M-TLA33 model.

Wire Gauge and Torque Settings

Provides wire gauge and torque settings for CuAl and Cu wires.

Installation Example 140G-M-TLA2A3

Assembly Procedure

Details the assembly procedure for the 140G-M-TLA2A3 model.

Wire Compatibility and Torque

Shows compatible wire sizes and required torque for the model.