Allen-Bradley LSIG-MM User Manual

(25) DIR 1000587R0002 (Version 02)
3.6.12. Summary table of protection functions
Current
protections
Disabling Disabling of TRIP only Start-up threshold Thermal memory
Trip Threshold Trip time
Trip
threshold
tolerance
(2)
Trip time
tolerance
(2)
L
all curves:
t=k/I2 and
IEC 60255-3

0.4xIn  I
1
 1xIn
step 0.01xIn
3s  t
1
 144s
(1)
, step 3s
@I
f
=3I
1
Release
between 1.05
and 1.2 xI1
±10%, I
f
 6In
±20%, I
f
 6In
S
(t=k)

0.6xIn  I
2
10xIn
step 0.1xIn
0.6xIn  I
2 start-up
10xIn
step 0.1xIn
I
f
>I2
0.05s  t
2
 0.8s, step 0.01s
0.10s  t
2 start-up
 30s, step 0.01s
0.04s  t
2 sel
 0.2s, step 0.01s
±7%, I
f
 6In
±10%, I
f
> 6In
The best of the
two data±10%
or 40ms
S
(t=k/I
2
)

0.6xIn  I
2
10xIn
step 0.1xIn
0.05s  t
2
 0.8s,
step 0,01 s @I
f
=10In
±7%, I
f
 6In
±10%, I
f
> 6In
±15%, I
f
 6In
±20%, I
f
 6In
I
(t=k)

1.5xIn  I
3
15xIn
step 0.1xIn
1.5xIn  I
3 Start-Up
 15x In
 30 ms
0.1s  t
3 start-up
 30s, step 0.01s
@ I
f
>I
3
±10%
G
(3) (4)
(t=k)

0.1xIn  I
4
1xIn
step 0.02xIn
0.1s  t
4
1s, step 0.05 s
0.1s t
4 start-up
 1s, step 0.02s
0.04s  t
4 sel
 0.2s, step 0.01s
@ I
f
>I
4
±7%
The best of the
two data±10%
or 40ms
G
(3) (4)
(t=k/I
2
)

0.1xIn  I
4
1xIn
step 0.02xIn
0.2xIn  I
4 Start-Up
 1x I
4
0,1s  t
4
 1s, step 0.05s
(minimum trip time)
@I
f
>4In
±7% ±15%
U
(t=k)

2%  I
6
 90%
step 1%
0.5s  t
6
 60s, step 0.5s ±10%
The best of the
two data±10%
or 40ms
OT
(temp=k)

Fixed Instantaneous ± 5°C
LC1/LC2
load Control

50%100% step 1%xI
1
Warning Iw

0.310I
n
step 0.05xI
n
± 10% 1040 ms
MM
(t=k)

1.5xIn  I
5
 4xIn
step 0.1xIn
 30 ms
@ I
f
>I
5
±10%
(1)
The minimum value of this trip is 1s regardless of the type of curve set (self-protection).
(2)
These tolerances are based on the following assumptions:
- energized trip unit in service conditions (without start-up) with 2 or 3 phases energized and/or
in the presence of auxiliary supply.
- Preset trip time  100 ms.
- Temperature and currents inside working ranges.
(3)
Protection G can be automatically disabled by the trip unit on the basis of the current measured.
For different cases see 3.6.5.
(4)
Minimum threshold for G protection, without Vaux, is 0.2 In.
For all cases not covered by the above hypotheses, the
following tolerance values apply:
Protection Trip threshold Trip time
L
Release between
1.05 e 1.25 x I1
± 20%
S ± 10% ± 20%
I MM ± 15%  60ms
G ± 10% ± 20%
Others ± 20%

Allen-Bradley LSIG-MM Specifications

General

Brand	Allen-Bradley
Model	LSIG-MM
Category	Circuit breakers
Language	English