EasyManua.ls Logo

Alliance Laundry Systems DC0220SFG - User Manual

Alliance Laundry Systems DC0220SFG
60 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
www.alliancelaundry.com
START
25
C
HIG
H
T
E
MP
MED
TEMP
L
OW
T
E
MP
NO
HE
A
T
1
2
3
SELECT
TE
M
P
I
N
S
ER
T
CO
I
N
P
US
H
S
T
A
R
T
T463PE1A
Tumble Dryers
25 Pound (220 liter)
30 Pound Stack (300 liter)
30 Pound (270 liter)
35 Pound (350 liter)
Refer to Page 5 for Model Numbers
Part No. 70143101R3
November 2016
Service

Table of Contents

Questions and Answers

  • W
    westhollyAug 16, 2025
    Why won't the burner ignite on my Alliance Laundry Systems Dryer?
    • G
      Glenn MonroeAug 16, 2025
      If the burner on your Alliance Laundry Systems Dryer isn't igniting, several issues could be the cause. Check for blown fuses or a tripped circuit breaker, ensure the gas shut-off valve is open, and verify sufficient gas supply and pressure. Also, inspect for lint buildup, proper ductwork, and adequate make-up air. The drying selector should not be set to the “Cool Down” portion of the cycle. Other potential causes include incorrect orifices, wiring issues, a faulty airflow switch, inoperative cabinet thermostat, or problems with the IEI control or motor switch. The lint drawer/panel must be closed properly. Refer to the Installation Instructions for exhaust system and make-up air requirements.
  • K
    kmorrowAug 19, 2025
    Why does the burner ignite and go out repeatedly on my Alliance Laundry Systems DC0220SFG Dryer?
    • T
      Tina DavisSep 12, 2025
      If the burner in your Alliance Laundry Systems Dryer ignites and then goes out repeatedly, it could be due to insufficient gas pressure, an inoperative cabinet thermostat, or an improper or inadequate exhaust system. Improper orifices, broken, loose, or incorrect wiring, excessive igniter to burner clearance, or inadequate make-up air could also be the cause. Refer to the Installation Instructions for exhaust systems and make-up air requirements.
  • J
    jburnsAug 22, 2025
    What to do if burners are not burning properly on Alliance Laundry Systems Dryer?
    • B
      Benjamin HendersonAug 22, 2025
      If the burners on your Alliance Laundry Systems Dryer are not burning properly, check for dirt in the burners and clean them if necessary. Ensure the gas pressure is correct according to the rating plate and that the correct orifices are installed. A restricted or blocked exhaust duct, a malfunctioning airflow switch, or inadequate make-up air could also be the cause. Refer to the Installation Instructions for make-up air requirements.
  • J
    Joseph BennettAug 25, 2025
    What causes the burner to not shut off on Alliance Laundry Systems DC0220SFG?
    • M
      Martin WongAug 26, 2025
      If the burner on your Alliance Laundry Systems Dryer does not shut off, it could be due to impurities on the gas valve seat, preventing the valve from closing, in which case the gas valve should be replaced. Incorrect wiring could also be a cause. Refer to the wiring diagram.
  • B
    Bryan SmithAug 28, 2025
    Why don't my clothes dry in my Alliance Laundry Systems DC0220SFG Dryer?
    • P
      Pam YorkAug 28, 2025
      Several factors can prevent your Alliance Laundry Systems Dryer from properly drying clothes. Ensure you're allocating enough heating time, and that the drying selector is appropriately set. Reduce the load size if it's too large (the maximum load is 25 lb dry weight for a 25 lb dryer). Also, make sure there isn't too much water in the clothes before drying. Check for a blocked exhaust duct or a clogged lint screen, and ensure the exhaust damper isn't binding. Other potential issues include an inoperative thermistor, burner problems, incorrect voltage, or inadequate make-up air. Refer to the Installation Instructions for exhaust system and electrical requirements.
  • S
    Scott BurnsAug 31, 2025
    Why does the motor overload protector cycle repeatedly on my Alliance Laundry Systems DC0220SFG Dryer?
    • W
      William GibbsAug 31, 2025
      If the motor overload protector in your Alliance Laundry Systems Dryer cycles repeatedly, it could be due to several reasons. The clothes load might be too large, or the cylinder could be binding. Check for correct voltage and adequate wiring, and ensure there's sufficient make-up air. Lint buildup around the dryer and motors can also cause this issue, as can broken, loose, or incorrect wiring. Refer to the Installation Instructions for electrical and make-up air requirements.
  • T
    Thomas ScottSep 3, 2025
    Why is my Alliance Laundry Systems DC0220SFG Dryer overheating?
    • A
      Andrew HurleySep 3, 2025
      If your Alliance Laundry Systems Dryer is overheating, it could be due to several factors. Ensure the correct main burner orifices are installed and that the gas pressure is properly adjusted. Check for lint buildup and ensure the exhaust system is not restricted or inadequate. Also, make sure there is adequate make-up air and that the exhaust damper is not binding. An inoperative thermistor sensor could also be the cause. Refer to the Installation Instructions for make-up air and exhaust system requirements.
  • J
    Jamie GordonSep 6, 2025
    What to do if motor runs but cylinder does not turn in Alliance Laundry Systems DC0220SFG?
    • J
      Joseph HayesSep 6, 2025
      If the motor in your Alliance Laundry Systems Dryer runs but the cylinder doesn't turn, the cylinder belt may be broken and needs replacement. Another possible cause is that the cylinder is binding, so check the cylinder for any obstructions.
  • J
    james86Sep 9, 2025
    Why does the motor not stop in my Alliance Laundry Systems DC0220SFG?
    • D
      Dr. Eric BurtonSep 9, 2025
      If the motor in your Alliance Laundry Systems Dryer does not stop, it could be due to an inoperative door switch or lint drawer switch, which should be tested and replaced if faulty. An inoperative coin drop or a malfunctioning electronic control could also be the cause. Incorrect wiring may also be responsible. Refer to the wiring diagram.
  • M
    Mathew SmithSep 12, 2025
    What to do if cylinder door opens during operation of Alliance Laundry Systems DC0220SFG Dryer?
    • M
      Mary MathewsSep 12, 2025
      If the cylinder door on your Alliance Laundry Systems Dryer opens during operation, it may be due to the dryer being improperly leveled. Also, an excessive load in the dryer can cause this issue; remove part of the load and restart the dryer.

Alliance Laundry Systems DC0220SFG Specifications

General IconGeneral
BrandAlliance Laundry Systems
ModelDC0220SFG
CategoryDryer
LanguageEnglish

Related product manuals