What to do if Alliance Laundry Systems HTT30N Dryer has spark but no flame?
If your Alliance Laundry Systems Dryer has a spark but no flame, first ensure the gas is on. Also, check for 24 VAC at the gas valve. If the issue persists, there might be a problem with the control; in this case check the voltage between the gas valve terminal MV and GND on the control.
Why Alliance Laundry Systems HTT30N valve is on but there is no spark during TFI?
If the valve is on but there's no spark during TFI in your Alliance Laundry Systems Dryer, it could be due to a shorted electrode. Another possible cause is an incorrect spark gap; ensure it's set to .094-.156 inch. Also, inspect the high voltage cable for faults or poor connections. Finally, control failure can cause this issue.
What to do if Alliance Laundry Systems Dryer flame is okay during TFI, but no flame sense after TFI?
If the flame is okay during TFI but there's no flame sense after TFI in your Alliance Laundry Systems Dryer, check the electrode position and cleanliness. Also, inspect the high voltage wire. Poor grounding at the burner or a poor flame (check flame current) can also cause this issue.
How to fix reset failure on Alliance Laundry Systems HTT30N Dryer?
If you're experiencing a reset failure on your Alliance Laundry Systems Dryer, it might be because the reset switch was pressed too long; try resetting again. Another possibility is that the reset switch is shorted, in which case you should replace the switch.
What to do if Alliance Laundry Systems HTT30N thermostat is on, but there is no spark or valve?
If the thermostat is on but there's no spark or valve activity in your Alliance Laundry Systems Dryer, first ensure the cable connects to the control and electrode, and that voltage is present at the gas valve. If the issue persists, the control might be bad; check the red LED for a steady on or flashing codes.
How to reset Alliance Laundry Systems HTT30N Dryer control in lockout mode?
If the control in your Alliance Laundry Systems Dryer is in lockout mode, a manual reset is needed. Reset it by pushing the red lockout button or use the front end control.
Why does my Alliance Laundry Systems HTT30N Dryer have nuisance shutdowns?
Nuisance shutdowns in your Alliance Laundry Systems Dryer can be due to a poor or erratic ground. To resolve this, verify that there is a proper system ground. Ensure the igniter, flame sensor, and igniter module share a common ground with the burner.
What to do if the Alliance Laundry Systems Dryer control is in lockout mode?
If the control panel on your Alliance Laundry Systems Dryer is in lockout mode, you will need to manually reset it. You can do this by pushing the red lockout button or using the front end control.
Lists all model numbers covered in the manual.
Key precautions for safe usage, installation, and maintenance.
General specifications like weight, dimensions, airflow, and ratings.
Details exhaust, gas, and electrical connection locations for models.
Steps for inspection, location, and material requirements before installation.
Guidance on making gas and electrical service connections.
Requirements for air supply and exhaust ducting to ensure proper operation.
Guidelines for sizing gas supply pipes and creating pressure-equalizing loops.
Guide for selecting correct burner orifices based on altitude.
Instructions for electrical wiring, grounding, and connection diagrams.
Details on converting voltage and electrical specifications for various models.
Guidelines for steam supply, return lines, and trap installations.
Information on configuring dry time and cool down via dipswitches.
Tables showing dipswitch configurations for heat time and cool down.
How to use the emergency stop, load, select cycles, and start the dryer.
Operation details for different control types like Dual Digital Timer and OPL.
Procedure for adjusting the air shutter for optimal combustion.
Adjusting airflow switch, loading door switch, and door strike.
Routine cleaning and inspection tasks for daily and monthly upkeep.
Procedure for testing the fire suppression system every three months.
Common problems and their possible causes and corrective actions.
Steps to safely disconnect the dryer from all utilities before removal.
Information on proper disposal according to WEEE directive.
General| Brand | Alliance Laundry Systems |
|---|---|
| Model | HTT30N |
| Category | Dryer |
| Language | English |
To Next Page