What to do if Alliance Laundry Systems Dryer has spark but no flame?
If your Alliance Laundry Systems Dryer has a spark but no flame, first ensure the gas is on. Also, check for 24 VAC at the gas valve. If the issue persists, there might be a problem with the control; in this case check the voltage between the gas valve terminal MV and GND on the control.
Why Alliance Laundry Systems HTT45N valve is on but there is no spark during TFI?
If the valve is on but there's no spark during TFI in your Alliance Laundry Systems Dryer, it could be due to a shorted electrode. Another possible cause is an incorrect spark gap; ensure it's set to .094-.156 inch. Also, inspect the high voltage cable for faults or poor connections. Finally, control failure can cause this issue.
What to do if Alliance Laundry Systems Dryer flame is okay during TFI, but no flame sense after TFI?
If the flame is okay during TFI but there's no flame sense after TFI in your Alliance Laundry Systems Dryer, check the electrode position and cleanliness. Also, inspect the high voltage wire. Poor grounding at the burner or a poor flame (check flame current) can also cause this issue.
How to fix reset failure on Alliance Laundry Systems Dryer?
If you're experiencing a reset failure on your Alliance Laundry Systems Dryer, it might be because the reset switch was pressed too long; try resetting again. Another possibility is that the reset switch is shorted, in which case you should replace the switch.
What to do if Alliance Laundry Systems HTT45N Dryer thermostat is on, but there is no spark or valve?
If the thermostat is on but there's no spark or valve activity in your Alliance Laundry Systems Dryer, first ensure the cable connects to the control and electrode, and that voltage is present at the gas valve. If the issue persists, the control might be bad; check the red LED for a steady on or flashing codes.
How to reset Alliance Laundry Systems Dryer control in lockout mode?
If the control in your Alliance Laundry Systems Dryer is in lockout mode, a manual reset is needed. Reset it by pushing the red lockout button or use the front end control.
Why does my Alliance Laundry Systems Dryer have nuisance shutdowns?
Nuisance shutdowns in your Alliance Laundry Systems Dryer can be due to a poor or erratic ground. To resolve this, verify that there is a proper system ground. Ensure the igniter, flame sensor, and igniter module share a common ground with the burner.
What to do if the Alliance Laundry Systems HTT45N Dryer control is in lockout mode?
If the control panel on your Alliance Laundry Systems Dryer is in lockout mode, you will need to manually reset it. You can do this by pushing the red lockout button or using the front end control.
Lists all models covered by the manual, categorized by Gas, Steam, and Electric types.
Explains DANGER, WARNING, CAUTION symbols and precautionary statements.
Provides crucial safety guidelines for operation and installation.
Covers weight, dimensions, performance metrics, motor specs.
Details cabinet dimensions for 025, 030, 035, 055 series.
Specifies exhaust outlet diameters and positions for 025-055 series.
Procedures for checking crate, carton, and parts for shipping damage.
Guidelines for selecting an appropriate installation site, avoiding water/weather.
Instructions for connecting the water supply for the fire suppression system.
Details electrical power supply needs and connection procedures.
Guidance on sizing gas supply pipes and installing loops for equal pressure.
Instructions for adjusting burner orifice size for operation at high altitudes.
Essential guidelines for electrically grounding the tumble dryer for safety.
Step-by-step procedure for connecting electrical service to the dryer.
Technical details on voltage, amperage, breaker ratings, and wire sizes.
Details steam pressure, pipe sizing, and connection considerations.
Guidelines for steam supply and return line installation and trap placement.
Instructions for configuring drying time using dipswitches on the control.
Tables detailing dipswitch configurations for various heat times.
Covers basic operation, safety warnings, cleaning, and loading.
Details operation for various controls like Dual Digital, OPL, DMP.
Details the operation of the DMP control, including programs and features.
Procedure for adjusting the air shutter for optimal burner performance.
Information on the airflow switch and its function in ensuring proper drying.
Instructions for adjusting the door switch and strike for proper operation.
Routine daily tasks for cleaning and inspection of the tumble dryer.
Procedure for testing the fire suppression system every three months.
A guide to identify and correct common operational issues before calling service.
Steps to safely disconnect and remove the tumble dryer from its installation.
Information on responsible disposal of the appliance according to WEEE directive.
General| Brand | Alliance Laundry Systems |
|---|---|
| Model | HTT45N |
| Category | Dryer |
| Capacity | 45 lbs |
| Heat Source | Gas |
| Voltage | 120/240V |
| Phase | 1 |
To Next Page