Programmable Out-
put Type Value
Mode(s) in Which
Available Signal is
Active
7 - Available with Vend
and End of Cycle
Ready Mode, End of Cy-
cle Mode, Partial Vend
Mode, Start Mode
8 - Machine is In Use Door Locking, Door/Lid
Unlocking, Overflow
Mode, Pause Mode, Run
Mode
9 - Cycle is Complete End of Cycle
10 - Lucky Cycle For 10 seconds when
Start Mode is entered
11 - Break in Alarm For 15 seconds when
Break in Alarm is trig-
gered at same time as au-
dio output tone
12 - End of Cycle is En-
tered
For 3 seconds when End
of Cycle Mode is entered
13 - Motor Running Whenever Motor is run-
ning
*Factory default setting.
Table 2
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Default Cycle dFtCyC
This option allows the owner to set the default cycle that the ma-
chine will enter when in the Ready Mode.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad until Prog appears in the display. Press the START
(enter) keypad, and AtS 1 will appear in the display.
3. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable options until
dFtCyC appears in the display.
4.
When dFtCyC appears in the display, press the START (en-
ter) keypad. A number will appear in the display. Refer to ta-
ble below. This number corresponds to the current default cy-
cle value. The corresponding LEDs will also be lit.
dFtCYC
Default Val-
ue Cycle Type
Wash Tem-
perature
1 NORMAL 90 90 °C
2 NORMAL 60 60 °C
3 * NORMAL 40 40 °C
4 PERM PRESS
60
60 °C
5 DELICATES 30 30 °C
6 DELICATES
COLD
Temperature of
water from tap
* Factory default setting.
Table 3
5. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to increase or decrease the current number to the de-
sired number.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Card Reader Display Control CArd
This option allows the owner to program whether the display is
controlled by the machine’s electronic control or an external pay-
ment system such as a card reader.
NOTE: This feature does not need to be programmed
manually. The card reader itself makes this determina-
tion.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad until Prog appears in the display. Press the START
(enter) keypad, and AtS 1 will appear in the display.
3. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to scroll through the programmable options until
CArd appears in the display.
4.
When CArd appears in the display, press the START (enter)
keypad. The current Card Reader Display Control Status will
appear in the display.
on = Card Reader/External Payment System controls display
oFF = Machine Electronic Control controls display (factory de-
fault setting)
5. Press the NORMAL 40 (∧) or the DELICATES COLD (∨)
keypad to change the current status.
Programming Control
©
Published by permission of the copyright owner -
DO NOT COPY or TRANSMIT
48 Part No. 805405ENR5
To Next Page
Loading...
Need help?
General