To Next PageTo Next PageWhat to do if my ALLIANCE Washer won't start?
If your ALLIANCE Washer isn't starting, make sure the lid is fully closed. Press the Start/Pause button to initiate the cycle. Check that the power cord is completely plugged into the electrical outlet. Ensure the controls are properly set for the desired wash cycle. Finally, verify that the laundry room fuse or circuit breaker is functioning correctly.
How to fix ALLIANCE TR5003WN not draining?
If your ALLIANCE Washer isn't draining, check the following: * Ensure the drain hose isn't kinked or twisted. * Make sure the drain hose isn't clogged. * Verify the drain receptacle is free from obstructions. Also, consult the Installation instructions to confirm the drain hose has been properly installed.
How to troubleshoot water leaks in ALLIANCE TR5003WN Washer?
If you notice water leaks from your ALLIANCE Washer, start by checking that the fill hoses are securely connected to both the faucets and the washer's water mixing valve. Inspect the fill hoses for wear and consider replacing them every five years. Ensure the drain receptacle isn't clogged, and examine your laundry room plumbing for any issues. Check your house water pressure, as extremely low pressure can sometimes cause leaks. Lastly, the laundry load might be oversudsing or overloaded; try using less detergent (or a low-sudsing detergent) and ensure you're using proper load sizes.
Why is my ALLIANCE TR5003WN Washer so noisy?
If your ALLIANCE Washer is making excessive noise, it could be due to a few reasons. First, the wash load may be unbalanced; open the lid and redistribute the items in the drum. Second, ensure the washer is level, as uneven leveling can cause vibration. If the washer is newly installed, a knocking sound may occur because the belt has settled during storage; run the washer through 4-5 cycles to loosen the belt. This won't affect the washer's operation.
Why is my laundry load too wet after washing in my ALLIANCE Washer?
If your laundry load is excessively wet after a wash cycle in your ALLIANCE Washer, the wash load may be unbalanced. Open the lid and redistribute the items. Also, the load might be too small; add more items to create a full load.
Why is my ALLIANCE Washer using the wrong water temperature?
If your ALLIANCE Washer is using the wrong water temperature, first, ensure that the controls are properly set. Check the fill hoses to confirm that the hot faucet hose is connected to the hot mixing valve (marked with “H”) and the cold faucet is connected to the cold mixing valve (marked with “C”). Verify that your laundry room water heater is adjusted to the correct temperature. Keep in mind that the Normal Eco cycle uses a colder water temperature.
How to reduce soap suds in ALLIANCE Washer?
If you're experiencing too many soap suds in your ALLIANCE Washer, the laundry load may be oversudsing. Make sure you are using low-sudsing, high efficiency (HE) detergent. Also, ensure you're using the amount of detergent recommended on the detergent’s label; if using non-HE detergent, use only 1/2 of the manufacturer's recommended amount. The laundry load may also be overloaded, so make sure you are using proper load sizes.
What to do if my ALLIANCE Washer stops and pauses during the cycle?
Pauses are a normal part of the ALLIANCE Washer's operation. The washer will stop (pause) shortly before the wash and rinse spins. You can also check the laundry room fuse or circuit breaker.
Why won't my ALLIANCE TR5003WN Washer agitate?
If your ALLIANCE Washer isn't agitating, make sure the lid is closed. Press the Start/Pause button to start the washer. Check that the power cord is fully plugged into the electrical outlet. Verify the laundry room fuse or circuit breaker. If these steps don't resolve the issue, the drive belt may be broken, and you should call a service person.
Why is my ALLIANCE Washer not spinning?
If your ALLIANCE Washer isn't spinning, make sure the lid is closed. Press the Start/Pause button to start the washer. Ensure the power cord is plugged all the way into the electrical outlet. Check the laundry room fuse or circuit breaker. If the problem persists, the drive belt may be broken, and you should call a service person.
General| Capacity | 3.2 cu. ft. |
|---|---|
| Color | White |
| Energy Star Certified | No |
| Wash Cycles | 8 |
| Spin Speed | 700 RPM |
| Voltage | 120 V |
| Type | Top Load |
| Width | 27 inches |
| Depth | 27 inches |
Covers critical warnings about installation, operation, fire, and explosion risks.
Defines DANGER, WARNING, CAUTION, IMPORTANT, and NOTE statements.
Provides critical precautions for safe washer operation and installation.
Details benefits like ownership verification and warranty service.
Covers pre-wash steps like emptying pockets, mending, and sorting.
Guides on how to properly load items into the washtub for optimal results.
Explains Auto Fill and manual water level settings for different load sizes.
Details recommended water temperatures for various fabric types and soil levels.
Provides advice on reducing energy consumption during washing.
Describes various wash cycles like Heavy Duty, Normal Eco, Perm Press, and Delicate.
Explains how to select the correct water level based on load size.
Details the extended wash time and soak period for heavily soiled items.
Explains the meaning of status lights and audio feedback during operation.
Step-by-step guide on loading clothes and starting a wash cycle.
Instructions on how to pause, resume, or cancel a wash cycle.
Outlines the stages, times, and settings for the Normal Eco cycle.
Details stages, times, and settings for specific heavy-duty and delicate cycles.
Explains the stages and settings for the Spin Only cycle.
Lists common washer sounds and their likely causes.
Introduces features like the Bleach Dispenser and Fabric Softener Dispenser.
Provides instructions for cleaning and using the fabric softener dispenser.
Addresses common clothing issues like dinginess, yellowing, tearing, lint, and wrinkling.
Instructions for protecting the washer in cold conditions and winterizing it.
Guidelines for cleaning the control panel, cabinet, and interior of the washer.
Covers replacing hoses and cleaning filter screens for optimal performance.
Advice on preparing the washer for periods of non-operation to prevent damage.
Outlines a schedule for checking hoses, lid switch, leveling, and tub cleaning.
Instructions on how to reinstall shipping brace and plug when moving the washer.
Addresses common problems related to the washer not filling or starting.
Solutions for issues like the washer not agitating or spinning correctly.
Explains normal pauses and how to address errors indicated by status lights.
Troubleshooting steps for problems with draining and water leaks.
Addresses causes and solutions for unusual noise, wet loads, and incorrect water temperatures.
Guidance on managing excessive suds and interpreting error codes.
Details specific error codes indicated by flashing status lights.
Information on obtaining warranty repairs and locating service providers.
Provides phone numbers, website, and mailing address for customer support.
