24-EN
Hands-Free Phone Control
Hands-free calls are possible when using a HSP (Head Set Profile) and
HFP (Hands-Free Profile) compatible mobile phone with this unit.
Notes
• Avoid performing a hands-free call in heavy traffic or on narrow or
winding streets.
• Close the windows while calling to reduce background noise.
• If both calling parties are using hands-free devices, or the call is made in
a noisy location, difficulty hearing the other person’s voice is normal.
• Depending on telephone line conditions or certain mobile devices used,
voices may sound unnatural.
• When using a microphone, speak as directly as you can into the
microphone to pick up the best sound quality.
• Certain mobile phone features are dependent on the capabilities and
settings of your service provider’s network. Additionally, certain features
may not be activated by your service provider, and/or the provider’s
network settings may limit the feature’s functionality.
Always contact your service provider about feature availability and
functionality.
All features, functionality, and other product specifications, as well as
the information contained in the Owner’s Manual are based upon the
latest available information and are believed to be accurate at the time
of printing.
Alpine reserves the right to change or modify any information or
specifications without notice or obligation.
Incoming calls are announced by the received call ring tone and a
displayed message (PHONE).
Press f or ENTER.
The call starts.
Notes
• When “AUTO ANS” is set to AT ANS ON, you can receive a call
automatically. Refer to “Setting the Received Calls automatically (Auto
Answer)” on page 23.
• While calling, the source sound on the unit is muted. After calling,
playback will resume.
• The caller name will not be displayed during phonebook updating.
Press f.
The call finishes.
Note
• You can also hang up the call by pressing and holding r for at least 2
seconds.
When a Smartphone equipped with voice recognition function is paired
with this unit, the Smartphone can be controlled by Voice Control via
this unit.
Press and hold VOICE CTRL for at least 2 seconds to
activate the Voice Recognition mode.
After the Voice Recognition mode is activated and “SPEAK” is
displayed, you can make a phone call, play a song, etc., via this
unit by inputting voice control commands
*
.
* Please refer to your Smartphone manual for other voice control
commands.
Notes
• You can perform this operation only when a Voice recognition
compatible mobile phone is connected. If the mobile phone is not
compatible with the Voice recognition, “NO SUPPORT” is displayed for
2 seconds.
• The Voice recognition function performance depends on the recognition
range of the mobile phone and mounting location of the microphone.
Please pay attention when the microphone is mounted.
• Voice recognition operation depends on the function of the mobile
phone. For details, refer to the Owner’s Manual of the mobile phone.
• If a called person that you say is not found, “NO CALL” is displayed for
2 seconds.
• Please obey all local traffic laws while using this function.
Call History is recorded for the last dialled/received/missed calls. There
are various ways of making calls based on the “Calling”. The following
steps 1 to 5 are common to the various ways of making these calls. For
details, refer to each individual category for making calls.
1
Press f.
The outgoing method list is displayed.
2
Turn the Rotary encoder to select the outgoing mode.
Setting contents:
DIALED / RECEIVED / MISSED / PHONE BOOK
DIALED:
Dialled history
RECEIVED:
Received history
MISSED:
Missed incoming history
PHONE BOOK:
Mobile phone book
3
Press ENTER.
The outgoing mode is activated, and each mode list is displayed.
Note
• It may take some time for the list to be displayed, and also directly after
connection, the list may not be brought up to date.
4
Turn the Rotary encoder to select a name or a telephone
number from the list.
Note
• You can use Phone book alphabet search function to search a name or
number from Phone Book. For details, refer to “Phone book alphabet
search function” on page 25.
5
Press ENTER.
The selected telephone will be called.
If one name has several numbers registered in the telephone
book, press ENTER after selecting the name
*
, then turn the
Rotary encoder to choose the desired number and press
ENTER, the telephone will be called. Depending on the
connected mobile phone, this function may not be performed.
* If the name cannot be recognised, default number will be
displayed.
Notes
•Press r to return to the previous mode.
• If no operation is performed for 60 seconds, the unit will return to
normal mode automatically.
• If there is no content in DIALED/RECEIVED/MISSED/PHONE BOOK
list, “----------” will be displayed for 2 seconds.
• If you place a call directly from the paired mobile phone, the phone
number is not displayed, you cannot redial from the unit in this case.
About the Hands-Free Phone
Answering a Call
Hanging up the Telephone
Voice Control Operation
Calling
00ALPINE.book Page 24 Monday, November 19, 2012 1:15 PM
To Next Page
Loading...
Need help?
General
