Installation
and
Connections
Before installing or connecting the unit, please read the
following and pages 5 to 7 of this manual thoroughly for
proper use.
&
Warning
MAKE
THE
CORRECT
CONNECTIONS
Failure to make the proper connections may result
in
fire or product
damage.
USE
ONLY
IN
CARS
WITH
A
12
VOLT
NEGATIVE
GROUND.
(Check with your dealer if you are not sure.) Failure to do so may
result
in
fire, etc.
BEFORE
WIRING,
DISCONNECT
THE
CABLE
FROM
THE
NEGATIVE
BATTERY
TERMINAL.
Failure to do
so
may result
in
electric shock or injury due to
electrical shorts.
DO
NOT
ALLOW
CABLES
TO
BECOME
ENTANGLED
IN
SURROUNDING
OBJECTS.
Arrange wiring and cables
in
compliance with the manual to
prevent obstructions when driving. Cables or wiring that obstruct or
hang
up
on
places such as the steering wheel, gear lever, brake
pedals, etc. can
be
extremely hazardous.
DO
NOT
SPLICE
INTO
ELECTRICAL
CABLES.
Never cut away cable insulation to supply power to other
equipment. Doing so will exceed the current carrying capacity
of
the wire and result
in
fire or electric shock.
DO
NOT
DAMAGE
PIPE
OR
WIRING
WHEN
DRILLING
HOLES.
When drilling holes
in
the chassis for installation, take precautions
so
as
not to contact, damage or obstruct pipes, fuel lines, tanks or
electrical wiring. Failure to take such precautions may result
in
fire.
DO
NOT
USE
BOLTS
OR
NUTS
IN
THE
BRAKE
OR
STEERING
SYSTEMS
TO
MAKE
GROUND
CONNECTIONS.
Bolts or nuts used for the brake or steering systems (or any other
safety-related system), or tanks should NEVER be used for
installations or ground connections. Using such parts could disable
control
of
the vehicle and cause fire etc.
KEEP
SMALL
OBJECTS
SUCH
AS
BOLTS
OR
SCREWS
OUT
OF
THE
REACH
OF
CHILDREN.
Swallowing them may result
in
serious injury. If swallowed,
consult a physician immediately.
DO
NOT
INSTALL
IN
LOCATIONS
WHICH
MIGHT
HINDER
VEHICLE
OPERATION,
SUCH
AS
THE
STEERING
WHEEL
OR
GEARSHIFT.
Doing so may obstruct forward vision or hamper movement etc.
and results
in
serious accident.
IMPORTANT
Please record
the
serial
number
of
your
unit
in
the
space provided
below
and
keep
it
as
a permanent record.
The
serial number plate
is
located
on
the
bottom of
the
unit.
&
Caution
HAVE
THE
WIRING
AND
INSTALLATION
DONE
BY
EXPERTS.
The wiring and installation
of
this unit requires special technical
skill and experience.
To
ensure safety, always contact the dealer
where you purchased this product to have the work done.
USE
SPECIFIED
ACCESSORY
PARTS
AND
INSTALL
THEM
SECURELY.
Be
sure
to
use only the specified accessory parts. Use ofother than
designated parts may damage this unit internally or may not
securely install the unit
in
place. This may cause parts to become
loose resulting
in
hazards or product failure.
ARRANGE
THE
WIRING
SO
IT
IS
NOT
CRIMPED
OR
PINCHED
BY
A
SHARP
METAL
EDGE.
Route the cables and wiring away from moving parts (like the seat
rails) or sharp or pointed edges. This will prevent crimping and
damage to the wiring. If wiring passes through a hole
in
metal, use
a rubber grommet to prevent the wires insulation from being cut
by
the metal edge
of
the hole.
DO
NOT
INSTALL
IN
LOCATIONS
WITH
HIGH
MOISTURE
OR
DUST.
Avoid installing the unit
in
locations with high incidence
of
moisture or dust. Moisture or dust that penetrates into this unit may
result
in
product failure.
Precautions
•
Be
sure
to
disconnect
the
cable
from
the
(-)
battery
post
before
installing
your
IVA-DI06.
This
will
reduce
any
chance
of
damage
to
the
unit
in
case
of a short-circuit.
•
Be
sure
to
connect
the
color
coded
leads
according
to
the
diagram.'
Incorrect
connections
may
cause
the
unit
to
malfunction
or
damage
to
the
vehicle's
electrical
system.
•
When
making
connections
to
the
vehicle's
electrical
system,
be
aware
of
the
factory
installed
components
(e.g.
on-board
computer).
Do
not
tap
into
these
leads
to
provide
power
for
this
unit.
When
connecting
the
IVA-DI06
to
the
fuse
box,
make
sure
the
fuse
for
the
intended
circuit
of
the
IVA-DI06
has
the
appropriate
amperage.
Failure
to
do
so
may
result
in
damage
to
the
unit
andJor
the
vehicle.
When
in
doubt,
consult
your
ALPINE
dealer.
•
The
IVA-D
106
uses
female
RCA-type
jacks
for
connection
to
other
units
(e.g.
amplifier)
having
RCA
connectors.
You
may
need
an
adaptor
to
connect
other
units.
If
so,
please
contact
your
authorized
ALPINE
dealer
for
assistance.
•
Be
sure
to
connect
the
speaker
(-)
leads
to
the
speaker
(-)
terminal.
Never
connect
left
and
right
channel
speaker
cables
to
each
other
or
to
the
vehicle
body.
•
The
Display
must
be
completely
retracted
in
the
casing
when
installing.
If
it
is
not,
problems
may
occur.
•
When
installing
in
automobiles,
make
sure
the
Display
can
open/close
without
coming
in
contact
with
the
gear
shift.
SERIAL
NUMBER:
_
INSTALLATION
DATE:
_
INSTALLATION
TECHNICIAN:
_
PLACE
OF
PURCHASE:
_
79-EN
To Next Page
Loading...
