11
R
Y2
C Y1
W1
G
W2
Furnace Integrated
Control Module
Thermostat
Two-Stage Heating
with
Two-Stage Cooling
7ඟ6ගඉඏඍ+ඍඉගඑඖඏඟඑගඐ7ඟ6ගඉඏඍ&ඔඑඖඏ
7ඐඍකඕඛගඉග'එඉඏකඉඕ
6එඖඏඔඍ6ගඉඏඍ7ඐඍකඕඛගඉග7ඟ6ගඉඏඍ0ඌඍඔඛ
To use a single stage thermostat, move jumper located
to the left of the terminal strip labeled “Stage Delay” from
NONE to “5” or “10” minutes. This selection will cause the
FRQWUROWRUXQRQORZVWDJHIRUWKHVHOHFWHGWLPHRUPLQ-
XWHVWKHQVKLIWWR+,*+67$*(7KLVRSWLRQFRQWUROVERWK
cooling and heating modes. If the jumper is not moved, only
low-stage cool and low-stage heat will operate.
5 MINUTE DELAY
PERIOD WITH
JUMPER IN THIS
POSITION
10 MINUTE DELAY
PERIOD WITH
JUMPER IN THIS
POSITION
7ඟ6ගඉඏඍ+ඍඉගඑඖඏගඑඕඍඌඉඖඌ7ඟ6ගඉඏඍ&ඔඑඖඏගඑඕඍඌ
ඟඑගඐ6එඖඏඔඍ6ගඉඏඍ7ඐඍකඕඛගඉග'එඉඏකඉඕ
Refer to the unit wiring diagram for electrical connections.
When installed, the unit must be electrically grounded in
accordance with local codes or in the absence of local
codes, with the National Electrical Code, ANSI/NFPA No.
70, and/or the CSA C22.1 Electrical Code. Ensure low volt-
age connections are waterproof.
3&%$*6ගඉඏඍ'ඍඔඉඡ
WARNING
7ඉඞඑඌගඐඍකඑඛඓඎඍඔඍඋගකඑඋඉඔඛඐඋඓඟඑකඑඖඏගගඐඍඝඖඑගඕඝඛග
ඊඍඔඉකඑජඍඌඉඖඌඏකඝඖඌඍඌ
CAUTION
7ඉඞඑඌකඍකගඡඌඉඕඉඏඍකඍකඛඖඉඔඑඖඒඝකඡඌඝඍගඎඑකඍඝඛඍ
ඖඔඡඋඍකඋඖඌඝඋගකඛ
CAUTION
7කඍඞඍඖගඑඕකඍකඉඖඌඌඉඖඏඍකඝඛඍකඉගඑඖඌඝඍග
ඟඑකඑඖඏඍකකකඛඔඉඊඍඔඉඔඔඟඑකඍඛකඑකගඌඑඛඋඖඖඍඋගඑඖඟඐඍඖ
ඛඍකඞඑඋඑඖඏඋඖගකඔඛ9ඍකඑඎඡකඍකඍකඉගඑඖඉඎගඍකඛඍකඞඑඋඑඖඏ
For unit protection, use a time delay fuse or hacr circuit
breaker that is in excess of the circuit ampacity, but less
than or equal to the maximum overcurrent protection de-
YLFH'2127(;&(('7+(0$;,08029(5&855(17
'(9,&(6,=(6+2:12181,7'$7$3/$7(
8ඖඑග9ඔගඉඏඍ
Rated
Voltage
Minimum Supply
Voltage
Maximum Supply
Voltage
9 197 253
All line voltage connections must be made through weath-
HUSURRI¿WWLQJV$OOH[WHULRUSRZHUVXSSO\DQGJURXQGZLULQJ
must be in approved weatherproof conduit.