8 ENGLISH
Guidance and manufacturer’s declaration – electromagnetic emissions
Emissions test Compliance
RF emissions CISPR 11 Group 1
RF emissions CISPR 11 Class B
Harmonic emissions IEC 61000-3-2 Class A
Voltage fluctuations/flicker emissions Complies
IEC 61000-3-3
The Ameda Elite Breast Pump is intended for use in the
electromagnetic environment specified below.
The customer or the user of the Ameda Elite Breast Pump
should assure that it is used in such an environment.
-%$)#!,%,%#42)#!,%15)0-%.4NEEDSSPECIALPRECAUTIONS
regarding EMC and needs to be installed and put into service
according to the EMC provided in these Instructions for use.
0ORTABLEANDMOBILE2&COMMUNICATIONSEQUIPMENTCAN
AFFECT-%$)#!,%,%#42)#!,%15)0-%.4
Warning: The use of ACCESSORIES, transducers and cables
other than those specified, with the exception of transducers
ANDCABLEDSOLDBYTHE-!.5&!#452%2OFTHE!MEDA%LITE
Guidance and manufacturer’s declaration – electromagnetic immunity
./4%
U
T is the a.c. mains voltage prior to application of the test level.
IMMUNITY test
Electrostatic
discharge
%3$
IEC 61000-4-2
Electrical fast
transient/burst IEC
61000-4-4
Surge IEC 61000-4-5
Voltage dips,
short
interruptions
and
voltage variations on
power supply input
lines IEC 61000-4-11
0OWERFREQUENCY
(ZMAGNETIC
field IEC 61000-4-8
IEC 60601 test level
± 6 kV contact
± 8 kV air
± 2 kV for power
supply lines/± 1 kV for
input/output lines
¢K6LINESTOLINES
¢K6LINESTOEARTH
U
T dip in
U
TFORCYCLE
U
TDIPIN
U
TFORCYCLES
U
TDIPIN
U
TFORCYCLES
U
T dip in
U
TFORS
3 A/m
Compliance level
± 6 kV contact
± 8 kV air
± 2 kV for power
supply lines/± 1 kV for
input/output lines
¢K6LINESTOLINES
¢K6LINESTOEARTH
U
T dip in
U
TFORCYCLE
U
TDIPIN
U
TFORCYCLES
U
TDIPIN
U
TFORCYCLES
U
TDIPIN
U
TFORS
3 A/m
Electromagnetic environment – guidance
Floors should be wood, concrete or ceramic tile.
If floors are covered with synthetic material, the
RELATIVEHUMIDITYSHOULDBEATLEAST
-AINSPOWERQUALITYSHOULDBETHATOFATYPICAL
commercial or hospital environment.
-AINSPOWERQUALITYSHOULDBETHATOFATYPICAL
commercial or hospital environment.
-AINSPOWERQUALITYSHOULDBETHATOFATYPICAL
commercial or hospital environment. If the user
OFTHE!MEDA%LITE"REAST0UMPREQUIRES
continued operation during power mains
interruptions, it is recommended that the Ameda
Elite Breast Pump be powered from an
uninterruptible power supply.
0OWERFREQUENCYMAGNETIClELDSSHOULDBEAT
levels characteristic of a typical location in a
typical commercial or hospital environment.
The Ameda Elite Breast Pump is intended for use in the
electromagnetic environment specified below.
The customer or the user of the Ameda Elite Breast Pump
should assure that it is used in such an environment.
Breast Pump as replacement parts for internal components,
MAYRESULTININCREASED%-)33)/.3ORDECREASED)--5.)49
of the Ameda Elite Breast Pump.
Warning: The Ameda Elite Breast Pump should not be used
ADJACENTTOORSTACKEDWITHOTHEREQUIPMENT)FADJACENT
or stacked use is necessary, the Ameda Elite Breast Pump
should be observed to verify normal operation in the
configuration in which it will be used.
Electromagnetic environment – guidance
The Ameda Elite Breast Pump uses RF energy
only for its internal function. Therefore, its RF
emissions are very low and are not likely to cause
ANYINTERFERENCEINNEARBYELECTRONICEQUIPMENT
The Ameda Elite Breast Pump is suitable for
use in all establishments, including domestic
establishments and those directly connected to
the public low-voltage power supply network that
supplies buildings used for domestic purposes.
To Next Page
Loading...
Need help?
General
