Arthrex AR-3200-0020 - User Manual

Other manuals for Arthrex AR-3200-0020

Instructions For Use Manual69 pages

Questions and Answers

V
vgarrettAug 14, 2025
What to do if there is no video image on the Arthrex Control Unit monitor?
- A
  Austin OrtizAug 14, 2025
  If there's no video image on the monitor, ensure the Control Unit and monitor are plugged in and powered on. Confirm all cable connections are correct, rerouting video cables if needed, and check for any cable damage, replacing them if necessary. Also, ensure the camera head cable connector is fully inserted into the Control Unit's camera head receptacle. If the issue persists, try replacing the camera head with a working one to see if the original camera head or cable is faulty and needs repair.
S
Sean BrownAug 17, 2025
How to fix intermittent picture on Arthrex AR-3200-0020 Control Unit?
- C
  Cynthia MatthewsAug 17, 2025
  To fix an intermittent picture, first, reinsert the camera head connector card edge fully into the CCU camera receptacle. Flex the video and power cables; if the picture is affected, inspect and replace the cables as needed. If flexing the camera cable affects the picture, it may need factory repair or replacement.
S
Sarah WalkerAug 20, 2025
What to do if Arthrex AR-3200-0020 Control Unit camera does not power up?
- Q
  qbrownAug 21, 2025
  If the camera doesn't power up and the standby LED doesn't illuminate, ensure the power cord is plugged into both the CCU and a properly grounded receptacle. If it is, try replacing the power cord, as it may be faulty.
B
bwuAug 25, 2025
Why Arthrex AR-3200-0020 Control Unit camera will not white balance?
- J
  Jeffrey RodriguezAug 25, 2025
  If the monitor indicates “White Balance Fail”, it could be due to too much light, too little light, or the wrong color temperature light. Try moving the scope further away or closer to the white gauze during white balance, or adjust the LED Light Engine brightness accordingly.
T
Terry ColonAug 27, 2025
What to do if Arthrex Control Unit tablet continually restarts?
- D
  Danielle DawsonAug 27, 2025
  If the tablet continually restarts or won't progress beyond the Samsung startup screen, first, check the tablet cable and connector for any damage. Also, ensure you're using a Samsung model EP-TA10JWE charger with a minimum of 2.0A charge current and a USB 3.0 charger cable (both connectors) no longer than 6 ft. (1.83 meters). Replace the charger or cable if they don't meet these specifications.
J
jesse67Aug 30, 2025
How to fix poor color reproduction on Arthrex AR-3200-0020?
- K
  Kelli MartinAug 30, 2025
  To correct poor color reproduction, white balance the camera head.
L
Lisa PerezSep 3, 2025
How to fix Arthrex AR-3200-0020 system that does not boot up correctly?
- B
  Brent WashingtonSep 3, 2025
  If the system doesn't boot up correctly or banners don't display properly, power down the device, wait three minutes, and then restart the system.
S
steven16Sep 6, 2025
Why Arthrex Control Unit camera head buttons do not function?
- X
  xdaySep 6, 2025
  If the camera head buttons do not function as programmed, reprogram the camera head buttons. Note that this solution applies only to the Tablet Data Input device option.
G
gardnerbryceSep 9, 2025
What to do if AR-3200-1013 Tablet will not connect to Arthrex CCU?
- E
  ehernandezSep 9, 2025
  If the AR-3200-1013 Tablet will not connect to the CCU, update the SynergyUHD4 Software to v4.13.1 or newer.