Arthrex AR-3200-0021 - User Manual

Other manuals for Arthrex AR-3200-0021

Instructions For Use Manual69 pages

Questions and Answers

J
Jonathan WebbAug 14, 2025
What to do if there is no video image on the Arthrex Control Unit monitor?
- P
  paige68Aug 14, 2025
  If there's no video image on the monitor, ensure the Control Unit and monitor are plugged in and powered on. Confirm all cable connections are correct, rerouting video cables if needed, and check for any cable damage, replacing them if necessary. Also, ensure the camera head cable connector is fully inserted into the Control Unit's camera head receptacle. If the issue persists, try replacing the camera head with a working one to see if the original camera head or cable is faulty and needs repair.
N
Natalie WaltonAug 17, 2025
How to fix intermittent picture on Arthrex AR-3200-0021?
- L
  Luis RuizAug 17, 2025
  To fix an intermittent picture, first, reinsert the camera head connector card edge fully into the CCU camera receptacle. Flex the video and power cables; if the picture is affected, inspect and replace the cables as needed. If flexing the camera cable affects the picture, it may need factory repair or replacement.
J
Janet OrtizAug 21, 2025
What to do if Arthrex Control Unit camera does not power up?
- S
  Sarah RoyAug 21, 2025
  If the camera doesn't power up and the standby LED doesn't illuminate, ensure the power cord is plugged into both the CCU and a properly grounded receptacle. If it is, try replacing the power cord, as it may be faulty.
D
David BrownAug 25, 2025
Why Arthrex Control Unit camera will not white balance?
- J
  Jamie EvansAug 25, 2025
  If the monitor indicates “White Balance Fail”, it could be due to too much light, too little light, or the wrong color temperature light. Try moving the scope further away or closer to the white gauze during white balance, or adjust the LED Light Engine brightness accordingly.
M
Melissa AdamsAug 27, 2025
What to do if Arthrex AR-3200-0021 Control Unit tablet continually restarts?
- A
  Alexa MillerAug 27, 2025
  If the tablet continually restarts or won't progress beyond the Samsung startup screen, first, check the tablet cable and connector for any damage. Also, ensure you're using a Samsung model EP-TA10JWE charger with a minimum of 2.0A charge current and a USB 3.0 charger cable (both connectors) no longer than 6 ft. (1.83 meters). Replace the charger or cable if they don't meet these specifications.
M
monica70Aug 30, 2025
How to fix poor color reproduction on Arthrex AR-3200-0021?
- C
  Chad CarlsonAug 31, 2025
  To correct poor color reproduction, white balance the camera head.
C
Curtis WheelerSep 3, 2025
How to fix Arthrex AR-3200-0021 Control Unit system that does not boot up correctly?
- B
  Bryce AdkinsSep 3, 2025
  If the system doesn't boot up correctly or banners don't display properly, power down the device, wait three minutes, and then restart the system.
J
Joshua MunozSep 6, 2025
Why Arthrex AR-3200-0021 camera head buttons do not function?
- M
  Michael SmithSep 6, 2025
  If the camera head buttons do not function as programmed, reprogram the camera head buttons. Note that this solution applies only to the Tablet Data Input device option.
C
Cory RodriguezSep 9, 2025
What to do if AR-3200-1013 Tablet will not connect to Arthrex CCU?
- G
  Grace MorganSep 10, 2025
  If the AR-3200-1013 Tablet will not connect to the CCU, update the SynergyUHD4 Software to v4.13.1 or newer.