Arthrex AR-3210-0023 - User Manual

Other manuals for Arthrex AR-3210-0023

Instructions For Use Manual69 pages

Questions and Answers

D
Destiny PalmerAug 15, 2025
What to do if there is no video image on the Arthrex AR-3210-0023 monitor?
- D
  Daniel RuizAug 15, 2025
  If there's no video image on the monitor, ensure the Control Unit and monitor are plugged in and powered on. Confirm all cable connections are correct, rerouting video cables if needed, and check for any cable damage, replacing them if necessary. Also, ensure the camera head cable connector is fully inserted into the Control Unit's camera head receptacle. If the issue persists, try replacing the camera head with a working one to see if the original camera head or cable is faulty and needs repair.
D
David AdamsAug 18, 2025
How to fix intermittent picture on Arthrex Control Unit?
- D
  Darryl AndrewsAug 19, 2025
  To fix an intermittent picture, first, reinsert the camera head connector card edge fully into the CCU camera receptacle. Flex the video and power cables; if the picture is affected, inspect and replace the cables as needed. If flexing the camera cable affects the picture, it may need factory repair or replacement.
M
Michael RosarioAug 21, 2025
What to do if Arthrex AR-3210-0023 Control Unit camera does not power up?
- J
  John SmithAug 22, 2025
  If the camera doesn't power up and the standby LED doesn't illuminate, ensure the power cord is plugged into both the CCU and a properly grounded receptacle. If it is, try replacing the power cord, as it may be faulty.
T
thompsonelizabethAug 26, 2025
Why Arthrex Control Unit camera will not white balance?
- T
  Tracy KellyAug 26, 2025
  If the monitor indicates “White Balance Fail”, it could be due to too much light, too little light, or the wrong color temperature light. Try moving the scope further away or closer to the white gauze during white balance, or adjust the LED Light Engine brightness accordingly.
K
Kyle BakerAug 29, 2025
What to do if Arthrex AR-3210-0023 tablet continually restarts?
- R
  ryan68Aug 29, 2025
  If the tablet continually restarts or won't progress beyond the Samsung startup screen, first, check the tablet cable and connector for any damage. Also, ensure you're using a Samsung model EP-TA10JWE charger with a minimum of 2.0A charge current and a USB 3.0 charger cable (both connectors) no longer than 6 ft. (1.83 meters). Replace the charger or cable if they don't meet these specifications.
A
Amanda TrevinoSep 1, 2025
How to fix poor color reproduction on Arthrex Control Unit?
- M
  Mary IngramSep 1, 2025
  To correct poor color reproduction, white balance the camera head.
M
millerkimberlySep 4, 2025
How to fix Arthrex AR-3210-0023 system that does not boot up correctly?
- J
  Joseph HenrySep 4, 2025
  If the system doesn't boot up correctly or banners don't display properly, power down the device, wait three minutes, and then restart the system.
K
Karen NortonSep 7, 2025
Why Arthrex Control Unit camera head buttons do not function?
- S
  Stephanie EvansSep 7, 2025
  If the camera head buttons do not function as programmed, reprogram the camera head buttons. Note that this solution applies only to the Tablet Data Input device option.
K
Kevin GonzalezSep 12, 2025
What to do if AR-3200-1013 Tablet will not connect to Arthrex CCU?
- J
  John BarronSep 12, 2025
  If the AR-3200-1013 Tablet will not connect to the CCU, update the SynergyUHD4 Software to v4.13.1 or newer.