Asko TD25 - User Manual

Questions and Answers

C
Caroline Singh MDAug 13, 2025
Why does my Asko TD25 stop after 3 hours?
- C
  Christopher CampbellAug 13, 2025
  Your Asko Dryer might stop after 3 hours due to several reasons: * The washing may have been spun at too low a speed (less than 800 rpm). Try spinning at a higher speed. * The control unit might not have reset properly. Try switching the machine off for 30 minutes before restarting. * High ambient temperature combined with low element output and low drying temperature can lead to condensation formation. Try selecting another program and ensure good ventilation in the room. * Poor condensation could be due to blocked external air. Ensure that the external air has free passage. * A defective thermistor or control unit can also cause this issue. In such cases, consider replacing the thermistor or the control unit.
C
Caitlin BrockAug 16, 2025
What to do if my Asko Dryer stops mid-cycle?
- D
  Denise EvansAug 17, 2025
  If your Asko Dryer stops during a cycle, it could be due to several reasons: - The automatic overheating protection might have tripped. Open the door, clean the filter and condenser unit, and leave the door open long enough for the overheating protection to reset. - The overheat protection in the motor may have been tripped. Clean and check the motor; if necessary, replace it. - A defective control unit can also cause the dryer to stop. Replace the control unit.
S
Shawn NguyenAug 20, 2025
Why isn't my Asko Dryer drying clothes properly?
- K
  kenneth84Aug 20, 2025
  If your Asko Dryer isn't drying clothes effectively, consider these potential causes: - Air leakage at the door seals can affect drying results. Check the sealing strips. - Air leakage around the motor shaft can also impact drying performance. Check the seal around the motor shaft. - A defective rear thermistor can cause drying issues. Replace the thermistor. - A defective control unit can also be the reason. Replace the control unit.
X
xcalhounAug 25, 2025
What to do if my Asko TD25 is overfilling and stops?
- M
  Melissa WalkerAug 25, 2025
  If your Asko condenser dryer is overfilling and stops, here are a few things to check: * The condensation water tank might be full. Empty the tank and restart the machine. * The condensing water pump or hoses could be blocked. Clean the hoses and check the voltage and resistance in the drain pump. * The float or float switch may be defective. Check that the float hasn't gotten stuck and verify the function of the micro-switch. * The control unit might be faulty, preventing the pump from starting. Consider replacing the control unit.
J
Jacob HenryAug 28, 2025
How to fix a thermistor fault that stops my Asko TD25 Dryer?
- K
  Katherine AndersonAug 28, 2025
  If your Asko Dryer stops due to a thermistor fault, it could be that the front thermistor is defective or the control is not in contact with it. The suggested solution is to replace the thermistor.
S
Steven StephensSep 1, 2025
Why does my Asko Dryer take so long to dry?
- G
  Glen MillerSep 1, 2025
  Several factors can cause your Asko Dryer to take longer than expected: - A blocked lint filter restricts airflow. Clean the lint filter. - A blocked condenser unit also reduces efficiency, so clean the condenser. - Insufficient spinning of the washing can leave clothes too wet; ensure you spin at a minimum of 800 rpm. - Poor room ventilation can affect drying. Open doors to adjacent rooms to improve airflow. - If you are using an evacuation hose, ensure it is as short as possible and not blocked or bent.
D
Dr. Amy GarciaSep 5, 2025
How to fix an Asko Dryer that won't start?
- O
  ogutierrezSep 5, 2025
  If your Asko Dryer won't start, try these troubleshooting steps: - Ensure that the outer door is properly closed and that the door pin is activating the door switch. - Verify that the machine is receiving power by checking the fuses and connections.
L
Lisa FoleySep 8, 2025
Why is my Asko TD25 Dryer drying unevenly?
- J
  Julia PayneSep 8, 2025
  Uneven drying in your Asko Dryer can occur due to: - Mixing various types of items in the same load. Ensure that you are not mixing different types of items; remove the dry items. - Overfilling the machine. Make sure that the machine is not overfilled; remove some of the washing if necessary.