Norton is a brand associated with ASSA ABLOY Accessories and Door Controls Group, Inc., an ASSA ABLOY Group company.
Copyright © 2019-2020, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9360-1030-020 Rev 6 11/20
Norton Technical Product Support:
Monroe, NC 28112 USA
Phone: 800.438.1951 ext: 6030
TechSupport.Norton@assaabloy.com
nortondoorcontrols.com
Troubleshooting Guide
Problem Solution
Door closing too fast
1) Adjust Latch and/or Sweep valves on closer clockwise OR
2) Decrease Closing Speed on controller (see page 12)
Door closing too slow
1) Adjust Latch and/or Sweep valves on closer counterclockwise OR
2) Increase Closing Speed on controller (see page 12)
Door does not open to desired location
1) Repeat Home process (see page 13), OR
2) Increase Obst Delay, OR
3) Adjust Backcheck valve on closer counterclockwise, OR
4) Decrease spring force on closer body (door must still close in event of power failure (see page 12), OR
5) Ensure shoe is properly oriented on door (see page 11)
Door does not reach fully opened position
1) Repeat Home process (see page 13), OR
2) Increase Obst Delay, OR
3) Adjust Backcheck valve on closer counterclockwise, OR
4) Decrease spring force on closer body (door must still close in event of power failure (see page 12), OR
5) Ensure shoe is properly oriented on door (see page 11)
Door opens and closes repeatedly Change selector mode switch from H/O to On
Motor is driving in the wrong direction Change Mount (Push / Pull) on controller, reset Home process (see page 13), and save values
When door reaches open position,
door drifts toward closed position
Increase Hold Speed on controller (see page 17) until door stops drifting
When door reaches open position,
door drifts further open
Decrease Hold Speed on controller (see page 17) until door stops drifting
When door reaches open position, door bounces Decrease Slow Speed on controller (see page 17)
When signal is received, operator tries to open
door before auxiliary components are unlatched /
retracted
1) Conrm latch devices are getting proper power,
2) Conrm latch devices are receiving power long enough to fully retract - adjust Latch Retraction on
controller (see page 17) as needed,
3) If latch device is not retracting fast enough, increase Start Delay on controller (see page 17) to assure
latch device has had sufcient time to fully retract before operator starts opening door.
Error message says “Short Circuit” Turn off power to unit. Check wiring for short / cut.
Error message says “Over Voltage” Check incoming power - line voltage has exceeded 145VAC
Error message says “Under Voltage” Check incoming power - line voltage has dropped below 80VAC
Error message says “Aux1, Aux 2, or Aux 3 Stuck”
Disconnect Aux 1, 2, or 3 inputs and conrm error message goes away. If so, make sure input device is not
stuck (sending constant signal). Controller has a 3 minute protection limit.
Error message says “Comm Error” Inverter must be replaced
Error message says “Presence Detect” Unit has a presence detector attached and device has been activated
Error message says “Drive Disabled” Selector mode switch is in the “Off” position
Cover will not snap onto backplate
1) Wire protruding from under cover
2) Backplate is twisted / not mounted properly. (see page 7)
Cover will not stay on operator Cover extrusion has been stretched too wide and will not properly secure
When doors are closing Follower door hits astragal
on Master door and will not fully close
1) Conrm door with astragal is set to Master-Coordinator
2) Adjust ‘Master Stop’ value to move position where Master door will ‘stop’ and wait for Follower door to
fully close. Once Follower door has fully closed, Master door should then close.
To Next Page
Loading...
Need help?
General
