Why is there detergent residue in the dispenser of my Atag VA7016SRT Dishwasher after washing?
Detergent residue in the detergent compartment of your Atag Dishwasher after washing can occur if the compartment was damp when you added the detergent; ensure it's dry. Also, check that dishes aren't blocking the detergent compartment from opening properly.
How to fix if Atag Dishwasher is not cleaning dishes?
If your Atag Dishwasher isn't cleaning dishes properly, start by checking that the dishes aren't blocking the spray arms, preventing their rotation. Inspect the spray arm holes and bearings for blockages, cleaning them if necessary. Ensure you're using a suitable dishwashing program—a longer program may be required. Verify that you're using the correct detergent dosage based on your water hardness; too much or too little detergent can affect results. Check the detergent's expiration date, and avoid large packages of detergent. Make sure dishes are loaded correctly, avoiding covering porcelain with large bowls or placing tall glasses in corners. Ensure glasses and cups are placed to sit steadily. Finally, confirm the filters are correctly fitted and locked in the stop position.
Why does my Atag VA7016SRT Dishwasher leave spots or films on the dishes?
If your Atag Dishwasher is leaving spots or films on the dishes, it could be due to several reasons. Check the rinse aid dosage setting. If you are using all-in-one detergents, they might have insufficient drying effect, so switch detergents or deactivate the setting TAB and add salt and separate rinse aid. Ensure the salt compartment is full. Verify that your water softener setting is correct. Also, inspect the salt compartment lid to ensure it's properly tightened to prevent leaks. If you're washing crystal, high temperatures or too much detergent can cause etching; use lower temperatures and less detergent. Contact the detergent manufacturer for further advice.
How to improve drying in my Atag VA7016SRT?
If your Atag Dishwasher isn't drying dishes adequately, ensure the Auto Open option is activated. A fully loaded dishwasher performs better in drying, so try to fully load it. Check the rinse aid level and dosage, topping up if necessary or increasing the dosage. If you're using all-in-one detergents with insufficient drying effect while the TAB setting is activated, consider switching to separate detergents, deactivating the TAB setting, and adding salt and rinse aid separately.
What to do if my Atag Dishwasher isn't cleaning dishes properly?
If your Atag Dishwasher isn't cleaning dishes well, start by checking that the dishes aren't blocking the spray arms and preventing them from rotating. Also, inspect the spray arm holes and bearings for blockages, cleaning them if necessary. Ensure you're using a suitable dishwashing program—a longer program may be needed. Verify the detergent dosage is correct for your water hardness; too much or too little detergent can affect results. Check that the detergent isn't old. Make sure dishes are loaded correctly, avoiding overcrowding or covering items. Ensure glasses and cups are stable, and that the filters are correctly fitted with the handle locked in the stop position.
What causes a bad odor in my Atag Dishwasher and how to get rid of it?
A bad odor in your Atag Dishwasher can be caused by dirt around the seals and in corners. Clean these areas with a washing-up brush and a low-foaming cleaner. Also, running low-temperature programs for extended periods can contribute to odors. To combat this, run a higher temperature program once or twice a month. If the dishwasher hasn't been used for a while, running a self-cleaning program may also help.
Why does my Atag VA7016SRT leave spots on stainless steel or silver?
If your Atag Dishwasher is leaving spots on stainless steel or silver items, it may be due to contact with certain foodstuffs like mustard, mayonnaise, lemon, vinegar, salt, and dressings. Rinse these types of food off dishes if you're not starting the dishwasher immediately, and use the Rinse and hold program. Also, separate dishes made from different metals, such as silver, stainless steel, and aluminum, to avoid marks and tarnishing.
Why is there detergent residue in the detergent compartment of my Atag VA7016SRT Dishwasher?
If your Atag Dishwasher has detergent residue in the detergent compartment after washing, it could be because the compartment was damp when you added the detergent; ensure the compartment is dry before adding detergent. Also, check that dishes aren't blocking the detergent compartment from opening.
Why does water remain in my Atag Dishwasher after the cycle?
If your Atag Dishwasher has water remaining after a cycle, the filters may be blocked, so clean the coarse and fine filters. Check that the filters are correctly fitted and locked in the stop position. Also, inspect the drainage pump for debris, cleaning it if necessary. Ensure the drainage hose is free from kinks and sharp bends. Disconnect the drainage hose from the sink unit's water trap to check for blockages, ensuring the connection has an inner diameter of at least 14 mm.
What does it mean when my Atag VA7016SRT Dishwasher display shows "Run Self-cleaning program"?
When your Atag Dishwasher displays "Run Self-cleaning program", it means the dishwasher tub, spray arms, and spray pipes need cleaning. Run a self-cleaning program.
General| Type | Freestanding |
|---|---|
| Delay start | Yes |
| Child lock | Yes |
| Size | Full-size |
| Colour | Silver |
| Number of place settings | 16 |
| Dimensions (H x W x D) | 60 cm |
To Next Page
