Atag VA7114RT - User Manual

Questions and Answers

J
Julia TerryNov 26, 2025
Why does my Atag Dishwasher leave spots or films on dishes?
- N
  nhernandezNov 26, 2025
  If you're noticing spots or films on your dishes after washing in your Atag dishwasher, here's what could be happening: * The rinse aid dosage setting may be incorrect. Adjust the rinse aid dosage setting. * If the TAB setting is activated and you're using an all-in-one detergent with a poor drying effect, switch to separate detergents (salt and rinse aid) or deactivate the TAB setting. * The salt compartment might be empty. Top it up with salt. * The water softener setting could be incorrect. Adjust the water softener setting. * The water softener might be leaking salt. Check that the salt compartment lid is properly tightened. If the issue persists, contact the service department. * The temperature might be too high, or you might be using too much detergent, which can cause ...
T
Thomas WilliamsAug 27, 2025
How to improve drying performance of my Atag Dishwasher?
- S
  simmonskimberlyAug 27, 2025
  If your dishes aren't drying properly in your Atag dishwasher, consider the following: * The Auto Open option may not be activated. Ensure this setting is turned on. * The dishwasher might not be fully loaded. Try to fully load the dishwasher for optimal drying. * The rinse aid level might be low, or the dosage is set too low. Top up the rinse aid or increase the dosage level. * If you're using all-in-one detergent and the TAB setting is activated, it might have an insufficient drying effect. Consider switching to separate detergents (salt and rinse aid) or deactivating the TAB setting.
A
Amanda YoungAug 29, 2025
How to get rid of bad odour in my Atag VA7114RT Dishwasher?
- B
  Brian MarshallAug 29, 2025
  If you notice a bad odor coming from your Atag dishwasher, it could be due to: * Dirt around the seals and in corners. Clean these areas with a washing-up brush and a low-foaming cleaner. * Prolonged use of low-temperature programs. Try running a high-temperature program once or twice a month, or use the self-cleaning program.
C
Cody HurstAug 30, 2025
How to remove grease deposits from my Atag VA7114RT?
- J
  johnsonangelaAug 30, 2025
  If you're finding grease deposits in your Atag dishwasher, it's likely due to: * Using low-temperature programs for an extended period. Try selecting a program with Intensive mode, which uses a higher temperature to dissolve grease on heavily soiled dishes. Alternatively, run a self-cleaning program once or twice a month.
J
Jennifer PalmerAug 31, 2025
Why are there spots on my stainless steel or silver after using my Atag Dishwasher?
- C
  Christina FarmerAug 31, 2025
  If you're seeing spots on your stainless steel or silver items after washing them in your Atag dishwasher: * Some foods like mustard, mayonnaise, lemon, vinegar, salt, and dressings can cause spots if left on the items for too long. Rinse off these types of foods if you're not starting the dishwasher immediately. You can use the Rinse and hold program. * Contact between stainless steel and silver during dishwashing can cause spots. Aluminum can also cause spots on dishes. Separate dishes made from different metals, such as silver, stainless steel, and aluminum, to avoid marks and tarnishing.
E
Erica JonesSep 22, 2025
How to remove sticky white/blue film from dishes in my Atag Dishwasher?
- T
  Tiffany DunlapSep 22, 2025
  To remove a sticky white/blue film from dishes in your Atag Dishwasher, reduce the rinse aid dosage. If you have very soft water, you may want to dilute the rinse aid 50:50 with water.
C
Catherine SmithSep 16, 2025
How to prevent spots on stainless steel and silver in my Atag VA7114RT?
- A
  Ashlee HammondSep 16, 2025
  To prevent spots on stainless steel and silver in your Atag Dishwasher, rinse off foods like mustard, mayonnaise, lemon, vinegar, salt, and dressings promptly. Use the Rinse and hold program if you're not starting the dishwasher immediately. Keep silver, stainless steel, and aluminum dishes separate to avoid contact during washing.
N
Natalie FloresSep 18, 2025
Why is there detergent residue in the Atag VA7114RT Dishwasher compartment after washing?
- A
  Andrew FernandezSep 18, 2025
  Detergent residue in the compartment of your Atag Dishwasher after washing may occur if the compartment was damp when you added the detergent; ensure it's dry. Also, check that the dishes are not blocking the detergent compartment from opening properly.
E
Elizabeth SmithSep 9, 2025
What to do if the buttons on my Atag Dishwasher don't react?
- A
  alexacarrSep 9, 2025
  If the buttons on your Atag dishwasher aren't responding, it could be due to a few reasons: * You might be pressing the buttons too soon after opening the door. Wait a moment and try again. * The child lock (button lock) might be activated. See the chapter Settings for instructions on deactivating it. * The door might be closed. The buttons only work when the door is open. * The buttons might be dirty. Clean them with a dry or slightly damp cloth.
E
emmaunderwoodSep 6, 2025
What to do if water is left in my Atag VA7114RT Dishwasher?
- B
  bondstacySep 6, 2025
  If water remains in your Atag Dishwasher, start by cleaning the coarse and fine filters. Ensure the filters are correctly fitted with the handle locked in the stop position. Clean any debris from the drainage pump. Verify the drainage pump stop is in place. Check the drainage hose for kinks or blockages, ensuring it's properly connected and has an inner diameter of at least 14 mm.