Atag VA8114SRT - User Manual

Questions and Answers

R
rowejanetAug 18, 2025
Why won't my Atag Dishwasher start?
- D
  dana65Aug 18, 2025
  Your Atag Dishwasher might not start because: * The Start/Stop button wasn't pressed long enough; press and hold it until the display indicates the program has started. * The door isn't properly closed; ensure it is. * The door lock hasn't clicked; check the door lock and ensure it clicks into place. * A fuse or circuit breaker has tripped; check them. * The plug isn't in the socket; check the plug. * The water tap is off; check the water tap. * There are overflows/leaks; check for those. * The delayed start option is selected; press and hold Start/Stop for three seconds to cancel it. * You have opened the dishwasher to add more dishes while a program is in progress; close the door and wait.
G
gary32Aug 23, 2025
What to do if my Atag Dishwasher leaves spots or films on the dishes?
- B
  Brenda HuffAug 23, 2025
  If you're seeing spots or films on your dishes after using your Atag Dishwasher, it could be due to: * An incorrect rinse aid dosage setting. * The TAB setting being activated while using all-in-one detergent with insufficient drying effect; switch detergents or deactivate the TAB setting and add salt and rinse aid separately. * An empty salt compartment; top up with salt. * An incorrect water softener setting. * The water softener leaking salt; check that the salt compartment lid is properly tightened. * Too high a temperature or too much detergent, which can cause etching on crystal; wash crystal at a low temperature with less detergent.
E
Emily JenkinsAug 26, 2025
How to fix an Atag Dishwasher door that won't close?
- J
  jefferygreeneAug 26, 2025
  If you're having trouble closing the door of your Atag Dishwasher: * Check that the baskets are correctly positioned horizontally and that the middle basket's water connector is aligned with its spray pipe. * If the door lock doesn't click into place, open the door, press and hold the left navigation button and the Auto Open option button until the display flashes, wait until it stops, and then close the door again.
R
Rose BakerAug 27, 2025
What causes bad odour in my Atag VA8114SRT Dishwasher and how to remove it?
- E
  Edwin GuerreroAug 28, 2025
  A bad odor in your Atag Dishwasher could be caused by: * Dirt around the seals and in corners; clean these areas with a washing-up brush and low-foaming cleaner. * Using low-temperature programs for a prolonged period; run a program with a high temperature once or twice a month, or use a self-cleaning program.
M
Mr. James PerkinsAug 29, 2025
How to fix water remaining in the Atag Dishwasher?
- G
  George SpearsAug 30, 2025
  If water remains in your Atag Dishwasher after a cycle, check the following: * The filters may be blocked; clean the coarse and fine filters. * The filters may not be fitted correctly; ensure the filter handle is locked in the stop position. * There may be debris in the drainage pump; clean the drainage pump. * The drainage pump stop may be missing; check that the colored stop on the right in the bottom drain is in place. * There may be a kink in the drainage hose; ensure the hose is free from kinks and sharp bends. * The drainage hose may be blocked; disconnect the drainage hose where it connects to the sink unit's water trap and check for debris.
C
Cheyenne WilliamsSep 1, 2025
Why are there grease deposits in my Atag VA8114SRT Dishwasher?
- C
  Caleb Boyer Jr.Sep 1, 2025
  Grease deposits in your Atag Dishwasher are often due to: * Using low-temperature programs for too long; try using a program with Intensive mode, which uses a higher temperature to dissolve grease, or run a self-cleaning program once or twice a month.
A
ashleyreidSep 3, 2025
Why is there detergent residue in the detergent compartment of my Atag Dishwasher after washing?
- N
  nancywilliamsSep 3, 2025
  Detergent residue in the detergent compartment of your Atag Dishwasher after washing can occur if: * The compartment was damp when you added the detergent; make sure the detergent compartment is dry when adding detergent. * The compartment has been blocked; check that dishes are not preventing the detergent compartment from opening.
S
Samantha MeyerSep 5, 2025
Why are my dishes not dry enough in my Atag VA8114SRT Dishwasher?
- P
  Patricia AndersonSep 5, 2025
  If your dishes aren't drying properly in your Atag Dishwasher: * Ensure the Auto Open option is activated. * Make sure the dishwasher is fully loaded. * Check and top up the rinse aid, or increase the dosage. * If using all-in-one detergent with the TAB setting activated, try switching detergents or deactivating the TAB setting and using salt and rinse aid separately.
Z
Zachary MorrowSep 8, 2025
What causes spots on stainless steel or silver in my Atag VA8114SRT?
- T
  Tonya NovakSep 8, 2025
  Spots on stainless steel or silver in your Atag Dishwasher can be caused by: * Certain foods like mustard, mayonnaise, lemon, vinegar, salt, and dressings, if left on dishes for too long; rinse these off before washing and use the Rinse and hold program. * Contact between stainless steel and silver during dishwashing; separate dishes made from different metals to avoid marks and tarnishing.
D
debra10Sep 10, 2025
Why does my Atag VA8114SRT make a rattling sound when dishwashing?
- M
  Melissa NewtonSep 12, 2025
  A rattling sound in your Atag Dishwasher during operation suggests that: * The dishes are not correctly placed, or the spray arms are not rotating; ensure dishes are placed securely and that the spray arms can rotate freely.