What to do if initial or return temperature is too low in Atlantic WOYA060KLT Heat Pump?
If the initial temperature (T5) or return temperature (T6) is less than 2°C in your Atlantic Heat Pump, it could be due to a defective frost protection function. Check the frost protection function. Alternatively, the back-up might be disconnected. Reconnect the back-up to resolve this.
How to fix low hydraulic flow rate in Atlantic WOYA060KLT Heat Pump?
If the hydraulic flow rate is too low in your Atlantic Heat Pump, it might be due to circulation pump speed settings being too low. Check and adjust the circulation pump speed settings. Alternatively, a clogged filter valve could be the cause. Clean or replace the clogged filter valve to resolve this.
What to do if I see 'HP outgoing flow sensor error (T5)' on my Atlantic Heat Pump?
If your Atlantic Heat Pump displays a 'HP outgoing flow sensor error (T5)', it typically means there's a short circuit, the sensor is disconnected, cut off, or the sensor is defective. You should check the sensor connections and replace the sensor if necessary.
What to do if I see 'HP return flow sensor error (T6)' on my Atlantic WOYA060KLT Heat Pump?
If your Atlantic Heat Pump displays a 'HP return flow sensor error (T6)', it typically means there's a short circuit, the sensor is disconnected, cut off, or the sensor is defective. You should check the sensor connections and replace the sensor if necessary.
What to do if I see 'Circuit 2 sensor error (T12)' on my Atlantic Heat Pump?
If your Atlantic Heat Pump displays a 'Circuit 2 sensor error (T12)', it typically means there's a short circuit, the sensor is disconnected, cut off, or the sensor is defective. You should check the sensor connections and replace the sensor if necessary.
What to do if I see 'Outdoor temperature sensor error (T7)' on my Atlantic Heat Pump?
If your Atlantic Heat Pump displays an 'Outdoor temperature sensor error (T7)', it typically means there's a short circuit, the sensor is disconnected, cut off, or the sensor is defective. You should check the sensor connections and replace the sensor if necessary.
What to do if I see 'DHW tank sensor error (T8)' on my Atlantic WOYA060KLT?
If your Atlantic Heat Pump displays a 'DHW tank sensor error (T8)', it typically means there's a short circuit, the sensor is disconnected, cut off, or the sensor is defective. You should check the sensor connections and replace the sensor if necessary.
How to fix low hydraulic flow rate in my Atlantic WOYA060KLT?
If the hydraulic flow rate is too low in your Atlantic Heat Pump, it could be due to circulation pump speed settings being too low, or a clogged filter valve. To resolve this, increase the circulation pump speed settings and clean or replace the clogged filter valve.
What causes communication error in Atlantic Heat Pump and how to solve it?
A communication error between the interface board and the HP regulator board in your Atlantic Heat Pump suggests a wiring issue. Inspect and fix the wiring connections to resolve this.
Why is the initial temperature (T5) or return temperature (T6) < 2°C on my Atlantic WOYA060KLT Heat Pump?
If the initial temperature (T5) or return temperature (T6) is less than 2°C in your Atlantic Heat Pump, it could be due to a defective frost protection function or a disconnected back-up. Inspect and repair the frost protection function and reconnect the back-up.
The heat pump installation must meet the requirements related to the location of the heat pump.
The electrical installation must be carried out in accordance with current regulations.
Filling the installation with gas.
Start-up check-list.
This heat pump provides: Heating in winter, ...
Maximum operating pressure heating / hot water tank...
Outdoor temperature min/max, Max. heating water flow temperature...
Bend the pipes into position and make holes for them...
Choose the location of the appliance after discussion with the client.
Connections must be made on the same day the installation is filled with gas.
The sealing test must be carried out using a certified gas detector...
Before connecting the hydraulic unit to the installation, rinse out the heating system correctly...
Displays the user interface screens.
Steps for initial setup.
Overview of menu options.
Managing anti-legionella cycles.
Shows status of functions and actuators.
Function for drying concrete floors.
Lists and explains faults related to the hydraulic unit.
Procedure for filling the system with gas.
Checklist for starting up the unit.
General| Refrigerant | R32 |
|---|---|
| Heating Capacity | 6.0 kW |
| Energy Efficiency Ratio (Cooling) | 3.21 |
| Operating Temperature Range (Heating) | -15°C to 24°C |
| Power Supply | 220-240V, 50Hz, 1Ph |
| Dimensions (Outdoor Unit) | 800x333x554 mm |
| Type | Air-to-Air Heat Pump |
To Next Page
