How to fix low hydraulic flow rate in Atlantic Heat Pump?
If the hydraulic flow rate is too low in your Atlantic Heat Pump, it might be due to circulation pump speed settings being too low or a clogged filter valve. You should check and adjust the circulation pump speed settings or clean the clogged filter valve.
Why is the hydraulic flow rate low in my Atlantic Heat Pump?
If you're experiencing a low hydraulic flow rate in your Atlantic Heat Pump, it could be due to circulation pump speed settings being too low or a clogged filter valve. You should check and adjust the circulation pump speed settings, or clean the clogged filter valve.
What to do if initial or return temperature is too low in Atlantic WOYA 080 LFCA Heat Pump?
If the initial temperature (T5) or return temperature (T6) is less than 2°C in your Atlantic Heat Pump, it could be due to a defective frost protection function or a disconnected back-up. Check and repair the frost protection function, or reconnect the back-up.
Why is DHW cycle too long in Atlantic WOYA 080 LFCA?
If the DHW cycle is too long (more than 6 hours) in your Atlantic Heat Pump, it may be because of too much draw-off during the same cycle or a disconnected DHW back-up. Reduce the draw-off during the DHW cycle or reconnect the DHW back-up.
What causes frost on return circuit during defrost in Atlantic WOYA 080 LFCA Heat Pump?
If frost is detected on the return circuit when defrosting the outdoor unit (temperature < 2°C) in your Atlantic Heat Pump, the circulating water volume may be too low. Increase the circulating water volume.
How to fix communication error in Atlantic WOYA 080 LFCA Heat Pump?
If you're experiencing a communication error between the interface board and the HP regulator board in your Atlantic Heat Pump, check the wiring by inspecting and securing the wiring connections.
What to do if there is legionella cycle error in Atlantic Heat Pump?
If you encounter a Legionella cycle error in your Atlantic Heat Pump, it might be due to a disconnected DHW back-up. Reconnect the DHW back-up.
How to troubleshoot HP outgoing flow sensor error (T5) in Atlantic Heat Pump?
If there's an error with the HP outgoing flow sensor (T5) in your Atlantic Heat Pump, it could be due to a short circuit, disconnected or cut off sensor, a defective sensor, or another error. Check the sensor connections or replace the defective sensor.
How to troubleshoot HP return flow sensor error (T6) in Atlantic WOYA 080 LFCA Heat Pump?
If there's an error with the HP return flow sensor (T6) in your Atlantic Heat Pump, it could be due to a short circuit, disconnected or cut off sensor, a defective sensor, or another error. Check the sensor connections or replace the defective sensor.
What causes outdoor temperature sensor error (T7) in Atlantic WOYA 080 LFCA Heat Pump?
If there's an error with the outdoor temperature sensor (T7) in your Atlantic Heat Pump, it could be due to a short circuit, disconnected or cut off sensor, a defective sensor, or another error. Check the sensor connections or replace the defective sensor.
Details unit package contents and defines key technical terms for the heat pump.
Covers installation regulations, unpacking, handling, and refrigerant circuit safety protocols.
Details requirements and procedures for installing refrigerant connections between units.
Guidelines for installing the outdoor unit, including clearances and positioning.
Outlines the steps and precautions for installing the hydraulic unit.
Covers rules, pipe shaping, bending, and flare creation for refrigerant circuits.
Details the process of filling the refrigerant circuit and creating a vacuum.
Instructions for connecting to the heating circuit, system rinsing, and volume requirements.
Explains how to fill the system with water and purge air from the hydraulic unit.
General| Type | Air-to-Water Heat Pump |
|---|---|
| Refrigerant | R32 |
| Heating Capacity | 8.0 kW |
| Power Supply | 230V |
| Cooling Capacity | 7.0 kW |
To Next Page
