EasyManua.ls Logo

ATON AH66T - User Manual

ATON AH66T
90 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
AH66T
Multi-Source/Multi Zone Controller
INSTALLATION MANUAL

Table of Contents

Questions and Answers

  • S
    Stephanie SmithSep 8, 2025
    Why does the video switch but is incorrect on my ATON system?
    • M
      Michael OliverSep 8, 2025
      If the video switches but is incorrect on your ATON system, connect the source video correctly, ensuring that Source #1 video is connected to Input #1 of the switcher, Source #2 video to Input #2, and so forth. Connect the video outputs to the correct monitors, with Video output #1 going to the monitor in Zone #1, Video Output #2 to the monitor in Zone #2, and so on. Set the unit ID correctly.
  • R
    robert71Aug 23, 2025
    Why is there no audio in a specific zone on my ATON AH66T Controller?
    • P
      pinedajessicaAug 23, 2025
      If there's no audio in a specific zone with your ATON Controller, first, ensure the source is playing by pressing play, tuning the station, or turning the source on. Then, select a source for the zone using the front panel LEDs to verify the correct zone is selected. Also, adjust the volume and check the speaker wiring and pre-amp audio output connections.
  • B
    Barbara ReevesAug 25, 2025
    Why is there an audio “hum” or buzz through the ATON Controller system speakers?
    • M
      Michael LunaAug 25, 2025
      If you're experiencing audio hum or buzz through the system speakers of your ATON Controller, it could be due to a ground loop, high source input level, or faulty cables. To resolve this, test the AC outlet using a ground tester. Try reversing the AC plug of components with non-polarized ends plugged into the same outlet strip as the amplifier. Also, isolate the problem by disconnecting sources one at a time. Reduce the input level settings in the ATON configuration software. Check source equipment cables for damage and speaker wiring for shorts.
  • M
    Maxwell SmithAug 26, 2025
    Why is there no audio in ANY zone of my ATON AH66T?
    • S
      smithbrianAug 26, 2025
      If there is no audio in any zone with your ATON AH66T Controller, first, verify the AH66T is powered on. Also, check that any external amplifiers are powered on and that the source audio is properly connected to the AH66T.
  • W
    William NewmanAug 27, 2025
    Why is the audio quality poor on my ATON Controller?
    • A
      Allen MartinAug 27, 2025
      If you are experiencing poor audio quality with your ATON Controller, where the audio is unclear and the bass response is low, it could be due to speakers being out of phase, a defective speaker, incorrect left/right assignment of source or zone RCA cables, or a poor audio cable connection between the source and the AH66T. To fix this, correct the polarity of the speaker wiring. Check for physical damage to the speaker and ensure it has the appropriate power rating and at least 8 Ohm impedance. Isolate the issue to the source or zone and correct it. Verify and correct the connections.
  • J
    Jason HarmonSep 22, 2025
    Why is there no Page or Door Chime audio on my ATON system?
    • E
      Elizabeth ThompsonSep 22, 2025
      If there is no Page or Door Chime audio, and the music does not mute when the page or doorbell is activated on your ATON system, deactivate the Do-Not-Disturb setting. Verify and connect the A-Net to VIANet connection. Also, check if the zone is set to Do-Not-Disturb in the ATON SystemWorx software.
  • C
    Crystal WeaverSep 16, 2025
    Why are A-Net commands not working on my ATON system?
    • P
      Paula FloydSep 16, 2025
      If A-Net commands are not working on your ATON system, verify the wiring. Set the chassis unit ID correctly. Verify and correct the programming.
  • A
    Amanda MitchellSep 18, 2025
    Why are 3rd Party RS-232 commands not working with my ATON AH66T Controller?
    • D
      Deborah NelsonSep 18, 2025
      If 3rd Party RS-232 commands are not working with your ATON AH66T, connect the RS-232 controller. Correct the wiring and verify the correct DB-9 to RJ45 adapter is being used (DB9F-RJ45 NULL Modem). Configure the correct settings using the ATON configuration software.
  • M
    Michael ThomasSep 7, 2025
    Why is the video not switching when using V8 or V85 Video Router with my ATON system?
    • C
      Catherine BrooksSep 7, 2025
      If the video is not switching when using the V8 or V85 Video Router with your ATON system, connect Cat5 using the A-Net wiring color code and verify the connections. Also, verify and correct the programming, and ensure the V8 / V85 unit ID is set correctly.
  • J
    john04Sep 4, 2025
    Why is the incorrect source playing on speakers connected to my ATON AH66T Controller?
    • T
      treeseSep 4, 2025
      If the incorrect source is playing on the speakers connected to your ATON AH66T Controller, verify and correct the input connections. Also, verify and correct the speaker connections.

ATON AH66T Specifications

General IconGeneral
Zones6
Operating SystemAndroid
ConnectivityWi-Fi, Bluetooth
ProcessorQuad Core Cortex A9
Resolution720 x 1280