AutomationDirect DURAPULSE GS3-4030 - Page 155

5–5
Parameter Memory Addresses (continued)
Parameter Description Hexadecimal
Modbus
Decimal *
Octal
Volts/Hertz Parameters
P2.00
Volts/Hertz Settings 0200 40513 1000
 P2.01
Slip Compensation 0201 40514 1001
 P2.02
Auto-torque Boost 0202 40515 1002
 P2.03
Torque Compensation Time Constant 0203 40516 1003
P2.04
Mid-point Frequency 0204 40517 1004
P2.05
Mid-point Voltage 0205 40518 1005
P2.06
Min. Output Frequency 0206 40519 1006
P2.07
Min. Output Voltage 0207 40520 1007
P2.08
PWM Carrier Frequency 0208 40521 1010
 P2.09**
Slip Compensation Time Constant 0209 40522 1011
P2.10
Control Mode 020A 40523 1012
Digital Parameters
P3.00
Source of Operation Command 0300 40769 1400
P3.01
Multi-function Input Terminals (DI1 - DI2) 0301 40770 1401
P3.02
Multi-function Input Terminal 3 (DI3) 0302 40771 1402
P3.03
Multi-function Input Terminal 4 (DI4) 0303 40772 1403
P3.04
Multi-function Input Terminal 5 (DI5) 0304 40773 1404
P3.05
Multi-function Input Terminal 6 (DI6) 0305 40774 1405
P3.06
Multi-function Input Terminal 7 (DI7) 0306 40775 1406
P3.07
Multi-function Input Terminal 8 (DI8) 0307 40776 1407
P3.08
Multi-function Input Terminal 9 (DI9) 0308 40777 1410
P3.09
Multi-function Input Terminal 10 (DI10) 0309 40778 1411
P3.10
Multi-function Input Terminal 11 (DI11) 030A 40779 1412
P3.11
Multi-Function Output Terminal 1 (Relay Output) 030B 40780 1413
P3.12
Multi-Function Output Terminal 2 (DO1) 030C 40781 1414
P3.13
Multi-Function Output Terminal 3 (DO2) 030D 40782 1415
P3.14
Multi-Function Output Terminal 4 (DO3) 030E 40783 1416
 P3.16
Desired Frequency 0310 40785 1420
 P3.17
Desired Current 0311 40786 1421
 P3.18
PID Deviation Level 0312 40787 1422
 P3.19
PID Deviation Time 0313 40788 1423
 P3.20
Desired Frequency 2 0314 40789 1424
 P3.30
Frequency Output (FO) Scaling Factor 031E 40799 1436
P3.31**
2nd Source of Operation Command 031F 40800 1437
* For Modbus Decimal addresses used with CLICK PLCs,
insert another zero as the next-to-most-significant digit, e.g., 402333 instead of 42333.
** Some parameters are available only in later firmware versions of DURAPULSE drives.
Refer to P9.39 and “DURA
PULSE Parameter Summary” in Chapter 4 for more information.
 Parameter can be set during RUN Mode.
Chapter 5: DURAPULSE MODBUS Communications
DURAPULSE AC Drive User Manual
1st Ed. Rev. D 05/2013