ffffffffffffffffffffffffffffffffffffff
The system responds:
pA updated
To replace one stored profile with another, copy the replacement profile to the replaced profile;
for example, type:
copy p2 to p1
The above command copies the values of p2 into p1 so they are identical.
Table 4-2 summarizes the information that is described in detail in the following sections.
Table 4-2: Data Option Profiles
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
Profile Use To view, type: To edit, type: To activate, type
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
Active Settings used view set option value (Activated for
Profile, for data calls or view pA (e.g., set parity even) next data call)
pA To Store:
copy pA to p1
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
p0 Stored Data Profile view p0 Factory Profile copy p0 to pA
(Factory Profile) (Cannot be changed)
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
p1 Stored Data Profile view p1 program p1 copy p1 to pA
(Copied to pA
after self-test or
power failure)
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
p2 Stored Data Profile view p2 program p2 copy p2 to pA
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
p3 Stored Data Profile view p3 program p3 copy p3 to pA
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
p4 Stored Data Profile view p4 program p4 copy p4 to pA
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbc
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
Creating (Programming) a Data Option Profile
It is possible for you to program profiles p1, p2, p3, and p4. Profile 1 (p1) is automatically
loaded after a set self-test or power-up. The values of p1 should be set to your most frequently
used settings.
To change the option values of any of the stored profiles use the program command. The
program command provides a series of prompts to help you with this task.
The program command cannot
bbbbbb
be used to change option values in the active profile or the factory
profile p0. To change the active profile, use the set command (see a later section in this chapter,
"Setting Options: Changing Your Active Profile pA)."
Note: Speed and parity options can only be changed from your data terminal or PC by using
the set command or by pressing
BREAK
typing
AT
and pressing
RETURN
(providing
the Autoadjust option is on).
To program any of the four stored profiles, follow this procedure.
4-16 Chapter 4
To Next Page
Loading...
