Baker Ruskinn Concept-M - Screen 14: USB Memory Warning Screen

55 pages

Save Page as PDF

To Next Page

To Previous Page

Page 35 of 50

USB Alarm

The USB alarm will activate if the USB memory stick has been removed for longer than 5

minutes as a reminder to replace it after the log files have been copied to a computer for

analysis. This alarm can be dismissed by pressing the back arrow at the bottom right of

the screen for 5 minutes and then it will re-activate.

Screen 14: USB Memory Warning Screen

Main Page

Table of Contents2
Table of Figures4
Introduction6
Safety Instructions7
Regulatory Compliance8
European Region8
North American Region9
Precautions9
Symbols10
Table 1: List of Symbols10
Transport and Storage11
Location and Handling of the Concept Workstation11
Environmental Operating Conditions11
Service Requirements12
Electrical Supply Requirements12
Figure 1: Concept Rear Connections12
Table 2: Electrical Service Requirements12
Gas Supply Requirements13
Figure 2: Gas Connection Graphic13
Table 3: Fuse Ratings13
Table 4: Standard Gases13
Table 5: Additional Gases for Specific Operating Modes13
Concept Overview14
Front View14
Figure 3: Standard Concept Workstation with SPES Option14
Figure 4: Large Concept Workstation14
Front Interior Views15
Figure 5: Right Side Internal View15
Figure 6: Left Side Internal View15
Left Side View16
Figure 7: Left Side End Panel with Ultrasonic Humidity Option16
Right Side View17
Figure 8: Right Side End Panel17
Rear View18
Figure 9: Rear End Panel and Supply Connections18
Figure 10: Gas and Electrical Connections18
Using the Workstation19
Using the Interlock19
Interlock Overview19
Operating the Interlock Outer Door19
Icon 1: Interlock Outer Door19
Operating the Interlock Inner Door20
Transferring Material into the Workstation Chamber Via the Interlock20
Screen 1: Interlock Purge Options21
Removing Material from the Workstation Chamber Via the Interlock22
Hand Access to the Main Chamber23
Figure 11: Ezee -Sleeves23
Vacuum Operation24
Figure 12: Compressed Ezee-Sleeve for Entry24
Figure 13: Arm Inserted into Ezee-Sleeve (Shown with and Without Ezee-Sleeve)24
Figure 14: Foot Pedals for Right and Left Glove Ports25
Figure 15: Ezee-Sleeve before Vacuum25
Figure 16: Ezee-Sleeve after Vacuum25
Workstation Entry26
Figure 17: Glove Port Cap26
Figure 18: Glove Port Cap Stowage and Locator26
Figure 19: Glove Port Cap Storage Location Inside Workstation27
Workstation Exit28
Figure 20: Glove Port Cap28
Figure 21: Glove Port Locator28
Humidity Control29
Figure 22: Aquasorb Sachets - Empty and Charged29
Figure 23: Aquasorb Sachet in Workstation29
Figure 24: Condensate Plate30
Figure 25: Condensate Output and Tray30
Screens31
Main Screen31
Initial Settings Screen32
Screen 4: Initial Settings Screen with Ultrasonic Humidity Option32
Screen 5: Oxygen Level Set-Point Pop-Up32
Table 6: Settings Screen Column Functions32
Screen 6: 0% Oxygen Settings Screen with Aquasorb Humidity Option33
Environment Control34
Screen 7: Environment Control Overview34
Screen 8: Exit Gas Control Warning34
Data Log35
Screen 9: Trend Log35
Utilities36
Screen 10: Utilities Menu36
Icon 2: Internal Lights Control36
Oxygen Sensor Calibration37
Screen 11: Oxygen Sensor Calibration37
Help / Settings38
Screen 12: Help / Settings Menu38
Warnings39
Screen 13: Temperature Alarm Screen39
Screen 14: USB Memory Warning Screen40
Screen 15: Gas MIX Time Limit Warning Screen41
Screen 16: Input Gas Pressure Alarm42
Table 7: Audible Alarm Sounds42
Usb Trend Log43
Table 8: Trend Log Data Fields43
Cleaning and Service Requirements44
Service and Cleaning Overview44
Table 8: Cleaning and Service Details44
Cleaning Procedure - During and after each Use45
Cleaning Procedure - Deep Clean with Front Screens Removed46
Figure 26: Front Screen Pneumatic Connector Disconnection46
Icon 3: Front Screen Release46
Year Service49
Figure 27: Ceiling Panel Thumb Screws49
Figure 28: Ceiling Panel Handle and Grab Catch49
Figure 29: Large Detox Sachet50
Figure 30: Large Catalyst Sachets50
Figure 31: Gloveport Sleeves50
Troubleshooting51
The Workstation will Not Switch on51
The Circuit Breaker Trips51
Low Gas Pressure51
Excessive Gas Usage52
Internal Equipment Not Powering up52
The Workstation Is Only Partially Operational52
Warranty Information53
Disposal Information54
Contact Details55

Baker Ruskinn Concept-M - Screen 14: USB Memory Warning Screen

Table of Contents