To Next PageTo Next Page
Need help?Do you have a question about the Balboa ML551 and is the answer not in the manual?
General| Brand | Balboa |
|---|---|
| Model | ML551 |
| Category | Control Panel |
| Language | English |
Adjusting spa temperature using Cool and Warm buttons.
Switching between Standard, Economy, and Sleep modes.
Temporarily turning off spa functions for maintenance.
Controlling pump 1, including speed shifts and time-outs.
Controlling pump 2, including speed shifts and time-outs.
Controlling the blower, including speed settings and time-outs.
Controlling the spa light, including dimming options.
Programming automatic filter cycles for optimal spa operation.
Automatic activation of pumps/blower to prevent freezing.
Panel locking to prevent unintended changes.
Automatic cycle after pump/blower use for system cleaning.
Options for continuous or intermittent circulator pump operation.
Operation and suppression of the ozone generator.
Accessing system information like SSID and software version.
Customizing spa settings like reminders and temperature units.
Configuring address for Dolphin II robotic cleaner integration.
Step-by-step guide to changing user preference settings.
Overview of the ML400 panel and its functions.
The initial boot-up sequence and priming mode.
Displaying and adjusting the spa's set temperature.
Switching between Standard, Economy, and Sleep modes.
Temporarily disabling functions for maintenance.
Controlling pumps 1 and 2, including speed and time-outs.
Controlling the blower, especially with one pump.
How the circulator pump functions in different configurations.
Controlling the spa and fiber optic lights.
Operation and suppression of the ozone generator.
Automatic cleaning cycle following pump/blower use.
System protection against freezing temperatures.
Securing the panel to prevent unauthorized changes.
Programming filter cycles for system maintenance.
Accessing technical data like SSID and software version.
Customizing various spa operational settings.
Step-by-step process for modifying preference settings.
Understanding how settings are stored and retained.
Differentiating memory storage for settings vs. time.
Sequence of messages shown when the system powers on.
Interpreting error codes related to configuration issues.
Overview of different VL series panel models.
The initial boot-up sequence and priming mode.
Displaying and adjusting the spa temperature.
Controlling pumps 1, 2, and 3 (if applicable).
Activating and controlling the spa light.
How to set and confirm the current time.
Switching between Standard, Economy, and Sleep modes.
Managing automatic filter cycles for system maintenance.
Advanced programming of filter cycle start/stop times.
Methods to lock and unlock the control panel.
Methods to lock and unlock temperature adjustments.
Operation of the ozone generator during filtration.
Visual indicators during system power-on.
Understanding error codes related to system configuration.
Step-by-step instructions for removing the circuit board.
Step-by-step instructions for installing a new circuit board.
Indicates temperature is not current in Economy or Sleep mode.
Signals a configuration error preventing spa startup.
Reminder to replace the mineral cartridge.
Prompt to test and adjust spa water pH levels.
Prompt to test and adjust sanitizer levels.
Indicates a firmware installation problem.
Reminder to clean and condition the spa cover.
Prompt to remove, clean, and reinstall the spa filter.
Indicates incorrect system configuration.
Signals a firmware installation problem.
Inadequate water detected; check water level.
Potential inadequate water or flow; reset manually.
Reminder to drain and refill the spa.
Pump runs during Standby Mode to assist in draining.
Inadequate water detected; spa shut down.
Inadequate water detected; spa shut down, no auto-reset.
Spa operating in Economy Mode with specific display indicators.
Indicates continuous filtration is active.
Potential freeze condition; pumps/blower activate.
Spa could not trip GFCI; operation may be unsafe.
Inadequate water detected; follow prior action.
Inadequate water detected; check water level.
Sensor difference indicates flow problem; check water level.
"Overheat" condition; spa shut down. DO NOT ENTER WATER.
Pump stuck on; POWER DOWN SPA IMMEDIATELY.
"Overheat" condition; spa shut down. DO NOT ENTER WATER.
"Overheat" condition; spa shut down. DO NOT ENTER WATER.
Potential freeze condition; pumps/blower activate.
Persistent low flow; heater shut down, other functions continue.
Reminder to install a new filter.
"Overheat" condition; spa shut down, may reset at 107°F/41.7°C.
"Overheat" condition; spa shut down. DO NOT ENTER WATER.
Indicates a hardware failure; contact Balboa.
pH is high; add pH reducer.
pH is low; add pH increaser.
System entering Priming Mode upon initial actuation.
Indicates a hardware failure; contact Balboa.
Reminder to install a new mineral cartridge.
Reminder to install a new filter.
Prompt to remove, clean, and reinstall filter.
Reminder to clean and condition the spa cover.
Prompt to drain and refill the spa.
Prompt to test and adjust pH chemical levels.
Sanitizer level check reminder.
Indicates a hardware failure; contact Balboa.
Prompt to test and reset RCD.
Prompt to clean and condition wood components.
Sensor A jack not working; test/replace sensor.
Sensor B jack not working; test/replace sensor.
Sanitizer level is high; allow it to dissipate.
Sanitizer level is low; add sanitizer.
Standby Mode activated; press button to return to normal.
Operating in Standard-in-Economy mode, reverts to Economy.
Sensor A not working; test and replace sensor.
Sensor B not working; test and replace sensor.
Sensors out of balance; test and replace sensor.
Sensor A not working; test and replace sensor.
Sensor B not working; test and replace sensor.
Sleep Mode activated; display shows "SLP".
"Overheat" condition; spa shut down. DO NOT ENTER WATER.
Standby Mode activated; press button to return to normal.
Spa operating in Standard Mode; temperature display is current.
Pump stuck on; temperature rising. POWER DOWN IMMEDIATELY.
Pump stuck on; temperature rising. POWER DOWN IMMEDIATELY.
Reminder to test and reset GFCI.
Reminder to clean and condition wood components.
