Banner D10 Expert Series

To Next Page

Advanced sensor with dual displays for use with plastic fiber optics

• Easy-to-read 8-segment light bar indicator for teach and signal strength readout, plus

indicators for continuous readout of operating status (user configuration)

• Easy-to-set automatic Expert-style configuration options include Static and Dynamic

TEACH, and Window SET, plus manual adjustment for fine tuning

• Smart gain-control algorithm to maximize performance in low-contrast applications

• Fast 500-microsecond sensing response with improved crosstalk avoidance routine

(for two sensors) in Normal mode

• Selectable high-speed (HS) mode option for 200-ms response

• Extreme configuration flexibility via push buttons or a remote input wire

• Easy selection of Light/Dark Operate (LO/DO), 30 ms pulse stretcher (OFF-delay), and

response speed, via push buttons or a remote input wire

• Models available with visible red (680 nm) or visible green (525 nm) sensing beam

• Sleek, ultra-slim 10 mm housing, mounts to a standard 35 mm DIN rail

• Models with bussable power provide simplified wiring of up to 16 sensors and feature

improved temperature compensation for side-by-side mounting

Models

Model Description Cable* Outputs

Red Beam Green Beam

D10BFP D10BFPG

Standard sensor

2 m (6.5 ft) Cable

Bipolar NPN/PNP

D10BFPQ D10BFPGQ 6-pin Pico-style QD

Models with Bussable Power

D10B5FP - Main unit 2 m (6.5 ft) Cable Bipolar NPN/PNP

D10B2PFP - Sub-unit 2 m (6.5 ft) Cable Single PNP

D10B2NFP - 2 m (6.5 ft) Cable Single NPN

Standard 2 m (6.5 ft) cable models are listed. To order the 9 m (30 ft) cable model, add suffix "W/30" to the cabled model number. For

example, D10xFP W/30. Models with a QD connector require a mating cable. See Accessories.

WARNING: Not To Be Used for Personnel Protection

Never use this device as a sensing device for personnel protection. Doing so could lead to serious

injury or death. This device does not include the self-checking redundant circuitry necessary to allow its

use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-

energized sensor output condition.

Overview

The D10 Expert is an easy-to-use, DIN-rail-mountable fiber optic sensor. It provides high-performance sensing in low-contrast applica-

tions. Configuration options include Setup mode plus Static and Dynamic TEACH, and Window Set options, in addition to manual fine

adjustment, remote programming, and security push button lockout.

D10 Expert Series with Bar Graph Display and Discrete Output

P/N 117830 Rev. F 5/15/2013

0 117830 8

Main Page

Other manuals for Banner D10 Expert Series

Quick Start Guide12 pages

Need help?

Do you have a question about the Banner D10 Expert Series and is the answer not in the manual?

The D10 Expert Series is a sophisticated fiber optic sensor designed for high-performance sensing, particularly in low-contrast applications. It features a compact, DIN-rail-mountable housing with a large, easy-to-read 8-segment red bar graph display and bright green/yellow LEDs for intuitive programming and status monitoring.

Function Description:

The D10 Expert Series operates by emitting a visible red (680 nm) or visible green (525 nm) sensing beam, depending on the model. It detects changes in light intensity and translates these into discrete output signals. The sensor is capable of establishing a single switching threshold or a sensing window, which can be configured through various TEACH and SET modes. Its smart gain-control algorithm maximizes performance in challenging low-contrast scenarios. The device also incorporates an adaptive threshold system that continuously tracks minimum and maximum signal levels, automatically maintaining the optimal switchpoint.

Important Technical Specifications:

Sensing Beam: Visible red (680 nm) or visible green (525 nm).
Supply Voltage:
- Standard Sensors: 10 to 30V DC (10% max ripple) @ < 45 mA (exclusive of load).
- Models with Bussable Power: 12 to 30V DC (10% max ripple) @ < 45 mA (exclusive of load).
Output Configuration:
- Standard Sensors: Bipolar (1 NPN, 1 PNP).
- Bussable Power Main Units: Bipolar (1 NPN, 1 PNP).
- Bussable Power Sub-units: Single NPN or PNP output.
Output Rating:
- Standard Sensors: 150 mA max. load @ 25°C (derates 1 mA per °C increase).
- Bussable Power Models: 100 mA max. load (derates 1 mA per °C above 30°C).
Output Response Time: 500 microseconds (normal mode), 200 microseconds (high-speed mode).
Repeatability: 100 microseconds (normal mode), 66 microseconds (high-speed mode).
Delay at Power Up: 200 ms (standard), 850 ms (bussable power models).
Environmental Rating: IEC IP50, NEMA 1.
Operating Temperature: -10 to +55°C (+14 to 131°F).
Storage Temperature: -20 to +85°C (-4 to +185°F).
Relative Humidity: 90% @ 55°C (non-condensing).
Construction: Black ABS/polycarbonate alloy (UL94 V-0 rated) housing, clear polycarbonate cover.
Connections:
- Standard Sensors: PVC-jacketed 2 m or 9 m (6.5 ft or 30 ft) 6-wire integral cable or integral 6-pin Pico-style quick-disconnect.
- Bussable Power Main Units: PVC-jacketed 2 m or 9 m (6.5 ft or 30 ft) 5-wire integral cable.
- Bussable Power Sub-units: PVC-jacketed 2 m or 9 m (6.5 ft or 30 ft) 2-wire integral cable.

Usage Features:

Configuration: Offers Expert-style configuration options including Static TEACH, Dynamic TEACH, and Window SET, along with manual adjustment for fine-tuning. Configuration is achieved via two push buttons (Dynamic (+) and Static (-)) or a remote input wire.
Light/Dark Operate (LO/DO): Easily selectable via push buttons or remote wire.
Pulse Stretcher (OFF-delay): 30 ms pulse stretcher is configurable.
Response Speed: Selectable Normal (500 µs) or High-Speed (200 µs) mode.
Crosstalk Avoidance: Improved routine for two sensors in Normal mode.
Remote Programming: Allows for remote configuration and push button lockout for security.
Manual Adjust: Fine-tunes sensing sensitivity or adjusts sensing window size in Run mode.
Bussable Power Models: Designed for applications where multiple sensors are grouped tightly, featuring increased temperature compensation and simplified wiring. An accessory clamp is available to secure connected sensors on a DIN rail.
Indicators:
- 8-segment red bar graph for light-to-dark signal difference, sensing contrast, and relative signal strength.
- Green status LEDs for LO, DO, High Speed (HS), and OFF-Delay.
- Green LED for Power ON.
- Yellow LED for Output conducting.
Security: Push button lockout feature prevents undesired tampering with settings.

Maintenance Features:

Terminal Caps and Plugs: Replacement terminal caps and plugs are available (SA-D10B-CAP) to cover the beginning and end of a stack of connected sensors, ensuring electrical connection integrity.
DIN Rail End Stops: Metal DIN rail end stops (SA-DIN-CLAMP) are available to hold bussable power models together and maintain electrical connection.
Warranty: Banner Engineering Corp. provides a one-year limited warranty covering defects in material and workmanship.