Barska AX11556 User Manual

User’s Manual for Biometric Safe
A. Initialization Button
B. Battery Compartment
C. Bolts
D. Fingerprint Scanner
E. Indicator Lights
F
G
A
B
D
E
H
* Actual model may vary
See reverse side for more information
9/12
BC248
1. INSTALL BATTERIES
1. Remove Battery Compartment (B) cover
2. Insert 4 AA batteries and restore battery cover
3. Bolts (C) automatically extend when batteries are inserted
To retract bolts:
- Press and release Wake-Up Button (F)
- Place any finger on the Fingerprint Scanner (D)
- Bolts will retract
2. FINGERPRINT REGISTRATION
IMPORTANT:
The safe is in Factory Default mode, ANY fingerprint can
open the safe. Only successful registered fingerprint can
terminate Factory Default mode
During registration the door must remain open and the Bolts (C)
must be in the retracted position. Otherwise, the fingerprint will
not be saved
To retract bolts:
- Press and release Wake-Up Button (F)
- Place any finger on Fingerprint Scanner (D)
- Bolts will retract
1. Press and release Initialization Button (A)
2. Immediately place a finger on the Fingerprint Scanner (D)
- Hold finger still
- 1 beep will be heard recognizing the fingerprint; followed by
2 consecutive beeps
- Remove finger
- Registration is complete
Successful Registration
Registration is successful when a total of 3 beeps are heard
Unsuccessful Registration
2 short beeps will be heard; repeat registration process again
3. To register another fingerprint – repeat steps 1 - 2
3. TEST A REGISTERED FINGERPRINT
1. With safe door open, press and release Wake-Up Button (F)
- Bolts (C) will extend
2. Press and release Wake-Up Button (F)
- Place a non-registered finger on the Fingerprint Scanner (D)
- Bolts will stay extended
3. If the bolts retract with a non-registered fingerprint,
registration was unsuccessful; and safe remains in Factory
Default mode
- Repeat steps under FINGERPRINT REGISTRATION
4. Press and release Wake-Up Button (F)
- Place a registered finger on the Fingerprint Scanner (D)
- Bolts will retract
4. CLOSE/OPEN SAFE DOOR
CLOSE: Close door, press and release Wake-Up Button (F)
- Bolts will extend
OPEN: Press and release Wake-Up Button (F)
- Place a registered finger on Fingerprint Scanner (D)
- Bolts will retract
5. BEEP SOUND OPTIONS
Beep OFF: Press and HOLD the Initialization Button (A) until
the Indicator Lights (E) are flashing green – RELEASE the
Initialization Button
Beep ON: Press and HOLD the Initialization Button (A) until
the Indicator Lights (E) are flashing green followed by 1 beep
– RELEASE the Initialization Button
6. DOOR OPEN ALARM
Regardless of the beep sound option chosen (either On or Off)
the door alarm is fixed to beep
The alarm is activated when the safe door is open and Bolts
(C) are retracted
Within 5 seconds, the Indicator Lights (E) will start to
flash green
More than 5 minutes, the safe will start beeping every
10-20 seconds
Close safe door, press and release Wake-Up Button (F) to
extend the Bolts (C) to cease the alarm
With the safe door open and the Bolts (C) extended, no lights
or beeping will be heard
7. OPEN SAFE WITH EMERGENCY KEY
1. To expose the Emergency Key access, remove Logo
Plate (G) screws with provided Allen wrench
2. Insert Emergency Key into key access, and turn clockwise
to open
NOTE: Store Emergency Keys in a secure place, NOT inside
of the safe
C
F. Wake-Up Button
G. Logo Plate and Emergency
Key Access
H. External Battery Access
(optional)
WARNING
- New Safe is in Factory Default mode, ANY fingerprint
can open the safe. Only successful registered
fingerprint can terminate Factory Default mode.
- Register at least two different fingerprints and test a
few times before closing the safe door.
- Test with a non-registered fingerprint. If the safe
opens, the safe remains in Factory Default mode.
- Avoid leaving safe door open and unattended; it will
allow unauthorized individuals to add their fingerprints
and/or reprogram the safe, gaining full access to the
safe and the contents.
- Test the Emergency Keys and store them in a secure
place, NOT inside of the safe.
- To maximize the security and performance of the
safe, test registered fingerprints every 6 months.
Read all instructions before using this safe.
http://www.monomachines.com
http://www.monomachines.com

Barska AX11556 Specifications

General

Material	Steel
Quantity	1
Fireproof	No
Lock type	Electronic
Product color	Black
Number of bolts	2
Power source type	Battery
Number of keys included	2 pc(s)

Weight and Dimensions

Depth	127 mm
Width	279.4 mm
Height	374.65 mm
Weight	9525.44 g
Door thickness	4.7 mm
Interior dimensions (W x D x H)	374.65 x 63 x 368.3 mm

Summary

Fingerprint Registration Process

Factory Default Mode Warning

Any fingerprint can open the safe in Factory Default mode until registered.

Register First Fingerprint

Press Initialization Button, then place and hold finger for recognition.

Test Registered Fingerprints

Test with Non-Registered Finger

Place a non-registered finger to verify bolts remain extended.

Verify Factory Default Mode

If bolts retract with a non-registered fingerprint, safe is in default mode.

Test with Registered Finger

Place a registered finger; bolts should retract upon successful recognition.

Door Open Alarm System

Alarm Activation Conditions

Alarm activates when the safe door is open and bolts are retracted.

Emergency Key Access

Secure Storage of Keys

Store emergency keys in a secure location, not inside the safe.

Reset to Factory Default Mode

Initiate Factory Reset

Press and hold Initialization Button; re-insert batteries one by one.

Confirm Factory Default Mode

One beep followed by two consecutive beeps confirms reset.

Factory Default Mode Status

In factory default mode, any fingerprint can open the safe.

Low Battery Warning System

Low Battery Indicator

Three repetitive beeps when the door is closed indicate low batteries.

Safe Care and Maintenance

Protect Control Panel

Keep liquids away from the control panel to prevent damage.

Avoid Product Disassembly

Do not disassemble the product; contact customer service for repairs.