EasyManua.ls Logo

battioni Pagani WPT 600 - User Manual

Default Icon
43 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
WPT, KTS, KPS,
KTM, WSM
WPT, KTS, KPS, KTM, WSM
Litograa Reverberi - Pr
Rev. 03 del 03.02.2017
IT
GB
MANUALE ISTRUZIONI
PER L’USO E LA MANUTENZIONE
INSTRUCTION MANUAL FOR
USE AND MAINTENANCE
NOTICE D’EMPLOI
ET D’ENTRETIEN
GEBRAUCHS-UND
WARTUNGSANLEITUNGEN
HANDLEIDING VOOR HET
GEBRUIK EN HET ONDERHOUD
FR
DE
NL
Rotary vanes
vacuum pump
Centrifugal pump
Rotary postive displacement
lobes pump
Rotary postive displacement
lobes pump
Rotary lobes
vacuum pump
Via Cav. Enzo Ferrari, 2
43058 Ramoscello di Sorbolo (PR) - Italy
Ph. +39 0521 663203
Fax +39 0521 663206
www.bapag.it
info@bapag.it

Table of Contents

Questions and Answers

  • C
    Courtney FreemanAug 14, 2025
    Why is my battioni Pagani Water Pump overheating?
    • C
      cookthomasAug 14, 2025
      Overheating in your battioni Pagani Water Pump can occur due to several reasons. It could be caused by excessive pressure, which requires you to reduce the pressure. Other causes include excessive revs rate (reduce the revs rate), a dirty cartridge filter (follow the cleaning procedure), excessive operating time (reduce operating time), blades that are too long (trim blades to the correct size), insufficient lubrication (check oil level in tank, the oil pump correct functioning, the oil cock regulation), or an insufficient cooling system (adjust the cooling system).
  • B
    Billy GilmoreAug 17, 2025
    What to do if my battioni Pagani Water Pump has little vacuum or pressure?
    • M
      Mr. Michael CummingsAug 17, 2025
      If your battioni Pagani Water Pump is showing little vacuum or pressure, several factors could be the cause. The blades might be worn (replace blades), or some blades might be jammed in the rotor (disassemble the Rotary blades vacuum pump, clean and wash the rotor, blades, body). Other potential causes include air infiltration or leakage from the system (eliminate infiltrations), an undulated cylinder (smooth or replace the body), a dirty cartridge filter (follow the cleaning procedure), a misplaced reversing gear (remove reversing gear and position it correctly), or the crash protection system being enabled (lift the flanges and tighten the flange screws with 55 Nm).
  • B
    Bonnie ThompsonAug 25, 2025
    How to fix a battioni Pagani Water Pump that is beating against the external surface?
    • E
      Emily BranchAug 25, 2025
      If your battioni Pagani Water Pump is beating against an external surface, it might be because the revs rate is too low (increase revs rate) or the lubricating oil quantity is too high/low and not appropriate (clean Rotary blades vacuum pump and replace oil).
  • K
    Kathleen BartonAug 27, 2025
    Why is there no lubricating oil circulation in my automatic lubrication battioni Pagani WPT 600?
    • E
      Erica WalkerAug 27, 2025
      If there's no lubricating oil circulation in your automatic lubrication battioni Pagani Water Pump, it could be due to a few reasons. There might be air intake at pipe fittings (replace pipe fittings), the lubrication tube might be badly inserted in pipe fittings (insert lubrication tube correctly), or the oil pump chamber might contain air (full the pump chamber with oil).
  • R
    Richard GilmoreAug 30, 2025
    What causes smoke to come out of the discharge tube of a battioni Pagani WPT 600 Water Pump and how to solve it?
    • W
      william21Aug 31, 2025
      If smoke is coming out of the discharge tube of your battioni Pagani Water Pump, it's likely due to excessive lubrication. Adjust the lubrication to resolve this issue.
  • L
    Lucas McdanielSep 3, 2025
    What causes a battioni Pagani WPT 600 Water Pump power take-off not to rotate?
    • S
      Sheryl JamesSep 3, 2025
      If the power take-off of your battioni Pagani Water Pump does not rotate, it could be due to a broken blade (replace blades and check if rotor pin is bent) or a foreign body has entered the Rotary blades vacuum pump (remove foreign body).
  • J
    John MartinezSep 6, 2025
    What causes water to leak from the blanking caps or fittings of a battioni Pagani WPT 600?
    • C
      cameron10Sep 7, 2025
      If water leaks from the blanking caps or fittings of your battioni Pagani Water Pump, it is likely due to insufficient tightening. Tighten until there is no more leakage.
  • C
    Christina PittmanSep 10, 2025
    What to do if the sewage output from the discharge curve of my battioni Pagani Water Pump?
    • N
      nsmithSep 10, 2025
      If the sewage output is deviating from the discharge curve in your battioni Pagani Water Pump, it could be due to malfunctioning valves. Check the valves to ensure they are working correctly.
  • B
    bonniefaulknerNov 20, 2025
    Why does my battioni Pagani WPT 600 have no suction or no compression?
    • C
      Colin HansenNov 20, 2025
      If your battioni Pagani Water Pump has no suction or compression, it could be due to several reasons: * The handle is badly positioned (position the handle correctly). * The reversing gear is badly positioned (position the reversing gear correctly). * The rotary blades pump runs backwards (reverse direction of rotation). * All blades are jammed (disassemble the pump, clean and wash blades, rotor and body). * Blades protrude from rotor slots anomalously (disassemble the pump, clean and wash blades, rotor and body). * The rubber ball closes the overflow valve (increase passage of air inside valve). * [KPS] The plate is locked (unscrew the cap or vacuum adjustment valve where present placed on the filter cover and move the plate downward until releasing or unlocking it). * P...

Summary

Introduction

Warranty

Safety Information

Obligatory Safety Signs

Displays mandatory safety signs for work areas and around vacuum pumps.

Conditions and Limits of Use

Outlines installation compliance, intended use, and potential dangers.

General Information

Rotary Blades Vacuum Pump Versions

Details available series and versions (M, MA, P, D, H, G, GA, K, KA) of vacuum pumps.

Identification Label

Explains the information found on the pump's identification plate.

Use and Maintenance Instructions

Packaging, Storage, Handling and Transport

Instructions for packaging, storage conditions, and safe handling/transport of vacuum pumps.

Assembly and Installation Procedures

Covers pump installation, cooling systems, hydraulic connections, and disassembly.

Start Up and Tuning

Guides on initiating the pump, setting rotation direction, and initial tuning.

Lubrication System and Adjustment

Details on lubrication systems, oil types, quantities, and adjustment procedures.

Valve Descriptions and Adjustments

Explains overpressure and vacuum adjustment valves, including their availability.

Testing and Running In

Procedures for testing new pumps and the initial running-in period.

Operation and Control

Start, Operation, and Stop Procedures

How to start, operate, and safely stop the vacuum pump.

Controls and Protective Devices

Information on control devices, transmission protection, and pump guards.

Personal Protective Equipment

Specifies the required personal protective equipment (PPE) for operating the pump.

Troubleshooting

Maintenance and Technical Assistance

Cleaning Procedures

Instructions for body washing, flushing, and cleaning tanks and valves.

Valves Checking

Guidance on regularly checking the functionality of overflow and pressure/vacuum valves.

Blades Inspection and Replacement

Procedures for inspecting blade wear, checking dimensions, and replacement.

Rubber Ball and Gears Replacement

Steps for replacing rubber balls in valves and gears in gearbox versions.

Regular Servicing

A schedule and guide for routine maintenance tasks and checks.

Putting Out of Service and Demolition

battioni Pagani WPT 600 Specifications

General IconGeneral
Brandbattioni Pagani
ModelWPT 600
CategoryWater Pump
LanguageEnglish

Related product manuals