Bauer 20106E-B - Maintenance and Servicing; Cleaning, Maintenance, and Lubrication; Sanding Disc Replacement

Page 11;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 58339
EF;6GHIJ6KFGLIMNFLMG6MFMO6 E6GPJ
N,"8$*8,84*%,89%E*(W"4"83
%J(&4*9'(*#%8&$%#/*4"2"4,77V%*`/7,"8*9%"8%$."#%5,8',7%5'#$%
+*%/*(2&(5*9%&87V%+V%,%<',7"2"*9%$*4.8"4",81
GI%JK6!6MG%E6KLIPE%LMaPKH%;KIN%FOOLU6MGFT%IJ6KFGLIM-%
G'(8%$.*%J&)*(%E)"$4.%&2%$.*%$&&7%&22%,89%'8/7'3%$.*%$&&7%2(&5%"$#%*7*4$("4,7%&'$7*$%
+*2&(*%/*(2&(5"83%,8V%/(&4*9'(*%"8%$."#%#*4$"&81
GI%JK6!6MG%E6KLIPE%LMaPKH%;KIN%GIIT%;FLTPK6-%
U&%8&$%'#*%9,5,3*9%*<'"/5*8$1%%L2%,+8&(5,7%8&"#*%&(%W"+(,$"&8%
&44'(#=%.,W*%$.*%/(&+7*5%4&((*4$*9%+*2&(*%2'($.*(%'#*1
O7*,8"83=%N,"8$*8,84*=%,89%T'+("4,$"&8
1. S6;IK6%6FO]%PE6= inspect the general
condition of the tool. Check for:
• loose hardware
• misalignment or binding of moving parts
• cracked or broken parts
• damaged electrical wiring
• any other condition that may
affect its safe operation.
2. F;G6K%PE6= turn off the tool, remove the
Safety Key from the Switch, and disconnect
its power supply. Then, wipe external
surfaces of the tool with clean cloth.
3. Apply a light coat of paste wax to the Work
Table to make feeding material easier.
4. Periodically, wear ANSI-approved safety
goggles and NIOSH-approved breathing
protection and blow dust and debris out of
the motor vents using dry compressed air.
5. The Bearings on this Sander are sealed
and do not require lubrication.
6. QFKMLMRc%GI%JK6!6MG%E6KLIPE%
LMaPKH-%L2%$.*%#'//7V%4&(9%&2%$."#%/&)*(%
$&&7%"#%9,5,3*9=%"$%5'#$%+*%(*/7,4*9%&87V%
+V%,%<',7"2"*9%#*(W"4*%$*4.8"4",81
E,89"83%U"#4%K*/7,4*5*8$
1. Remove the Work Table if it is mounted
in front of the Sanding Disc.
2. /RRVHQWKHWZR6W௘௘[௘10 Screws (5)
holding the Disc Guard (6) in place
and remove the Guard.
3. Peel off old Sanding Disc.
4. Wipe down the Backing Disc with
denatured alcohol to remove any
residue and ensure a secure bond.
5. Remove backing from new Sanding Disc.
6. Align perimeter of new Sanding Disc
over the Backing Disc and press Sanding
Disc firmly onto the Backing Disc.
7. Replace the Disc Guard against the lower
1/3 of the Sanding Disc and fasten securely.
;"3'(*%L
E4(*)
E4(*)
U"#4%
R',(9
S,4b"83%
U"#4